|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
05-13-2017, 06:57 AM | #11 |
Old Sky Soldier
Join Date: Dec 2011
Location: Kentucky
Posts: 3,881
|
Re: Changing cart speed
It is on the end of the motor under the speed sensor. There are two types, one for the GE motor it is pressed on the end of the motor shaft, gray motor. Then the ADC motor has the magnet held on the end of the shaft by a screw. Black motor.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-13-2017, 08:28 AM | #12 |
Gone Wild
Join Date: Jan 2017
Location: Queensland Australia
Posts: 1,332
|
Re: Changing cart speed
Thanks again.
|
05-16-2017, 07:40 AM | #13 |
Gone Wild
Join Date: Jan 2017
Location: Queensland Australia
Posts: 1,332
|
Re: Changing cart speed
For those not versed in all of this, like myself, you may be interested in the answer to my original post. The following information is taken from Dave's Revolution Golf Cars ebay page on the speed magnet. I have only just found that page and the info is brilliant Dave. I hope you don't mind me plagiarising it here.
The 48V SepEx system is programmable. The factory options are:
To change the settings requires a dealer to get a code from Club Car to unlock the required setting, costing about $100. An alternate is to change the magnet on the front of the motor from an 8-pole magnet to a 4-pole one thus communicating with the speed sensor half as often. This theoretically doubles the speed settings but in reality the most you'll get are speeds around 20-24 mph assuming no drag caused by dragging brakes, poor wheel alignment, worn hub bearings etc. Two things to note with this change:
So the bottom line for a magnet change is that the speed is increased because it allows the motor to spin to a higher rpm (in effect it is no longer rev limited) but it does not change the amounts of power or torque put out by the motor. Beyond that there are upgraded motors, controllers, solenoids, cables and FNR switches. All of these are comprehensively catered for and documented by the site sponsors Dave at Revolution Golf Cars and scottyb at Carts Unlimited. I particularly found interesting the information that scottyb has on his site regarding the Alltrax controller and the new capability of Shift-on-the-fly which allows you to save programs and then switch on the move between speed priority and torque priority. http://www.cartsunlimited.net/shift-on-the-fly.html |
05-16-2017, 09:11 AM | #14 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: Changing cart speed
I will just add the speed magnet option is only for IQ carts (black controller), the Excel drive system (gray or white controller) does not support the speed magnet.
|
05-16-2017, 09:29 AM | #15 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Changing cart speed
I believe a speed controller from Alltrax is the best way to spend your upgrade allowance. I just spent the $ on a controller update to code 4 in my 2014 Precedent. I do see an increase in top speed but not so much up hill as the power is not there.
A simple 300(350 peak) or 400 amp(460 peak) Alltrax will net more torque and speeds up to 23 mph. 400 amps leaves the motor upgrade later option open |
05-16-2017, 03:52 PM | #16 |
Gone Wild
Join Date: Aug 2015
Location: summer-north,winter-south
Posts: 588
|
Re: Changing cart speed
Would this also be true for a GE motor on the CC? I read they can not handle the added amps. If what you said is true for GE motors, sounds like a perfect upgrade for me without sinking a ton of money into all the supporting parts.
|
05-16-2017, 06:16 PM | #17 |
revolutiongolfcars.com
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 10,224
|
Re: Changing cart speed
The GE motor has small brushes and can't withstand high amp loads like the ADC motor or aftermarket motors. I would feel comfortable running a 300 amp controller on it as long as you weren't pulling heavy loads.
|
05-16-2017, 07:52 PM | #18 | |
Gone Wild
Join Date: Aug 2015
Location: summer-north,winter-south
Posts: 588
|
Re: Changing cart speed
Quote:
Also I did a little reading up on that Alltrax and in some places it says all of them require a HD solenoid upgrade. For me this might be the perfect solution. I need the torque mostly, but would like to go beyond 15mph (code 3) at times. Like the regen part of the IQ system also. Got a few hills to deal with. |
|
05-16-2017, 08:25 PM | #19 | |
Gone Wild
Join Date: Aug 2015
Posts: 177
|
Re: Changing cart speed
Quote:
|
|
05-16-2017, 08:28 PM | #20 | |
revolutiongolfcars.com
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 10,224
|
Re: Changing cart speed
Quote:
|
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Changing the motor on my cart | Gas Yamaha | |||
Changing to a PWM from resistor speed cntrl. | Extreme DC! | |||
Changing Tires CC CarryAll Gas--- Significant Speed Increase!! | Gas Club Car | |||
changing oil in lifted cart | Gas Yamaha | |||
Changing the OBC on 95 DS cart. | Electric Club Car |