|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
12-05-2014, 05:53 PM
|
#1 |
|
Not Yet Wild
Join Date: Dec 2014
Posts: 8
|
1986 ezgo will not start
I have good fire , have 135-140 lbs. compression. New spark , new coil new igniter carb kit installed in carb.
.will flood out engine block. Will only pop doesn't even try to start. should the hole under the fuel pump blow or suck |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
12-05-2014, 07:30 PM
|
#2 |
|
Test before replacing
Join Date: Aug 2013
Location: Ohio side of the Pennsylvania border.
Posts: 3,495
|
Re: 1986 ezgo will not start
It should do both. When blowing, it should push your finger off pretty good.
You said flooded engine block. Since you have the fuel pump off, take it apart, and check the lower diaphragm for rips. Looking at everything that you have listed, you are down to fuel pump, and crankshaft seals. |
|
|
|
|
12-06-2014, 10:58 PM
|
#3 |
|
It ain't gonna be easy.
Join Date: Apr 2008
Location: St. George, SC
Posts: 1,480
|
Re: 1986 ezgo will not start
Agree with Cart..... The fuel pump diaphragm is probably leaking fuel back into the block. Crankcase pressure pulses drive the pump.
|
|
|
|
|
12-07-2014, 04:42 PM
|
#4 |
|
Not Yet Wild
Join Date: Dec 2014
Posts: 8
|
Re: 1986 ezgo will not start
Will look , but has a new fuel pump kit installed.
Thank You With fuel pump on , it will not suck in at carb. |
|
|
|
|
12-07-2014, 05:06 PM
|
#5 |
|
Test before replacing
Join Date: Aug 2013
Location: Ohio side of the Pennsylvania border.
Posts: 3,495
|
Re: 1986 ezgo will not start
No suction at the carb would make me think that the piston is in backwards, or the crankshaft seals are junk.
Was this a recent rebuild? |
|
|
|
|
12-07-2014, 07:33 PM
|
#6 |
|
Not Yet Wild
Join Date: Dec 2014
Posts: 8
|
Re: 1986 ezgo will not start
piston and rings replaced, installed piston with hole to carb side.
|
|
|
|
|
12-07-2014, 08:10 PM
|
#7 |
|
Test before replacing
Join Date: Aug 2013
Location: Ohio side of the Pennsylvania border.
Posts: 3,495
|
Re: 1986 ezgo will not start
Did you align the end of the rings with the little pins in the ring grooves?
What was the result of putting your finger over the fuel pump hole while turning it over? Good pressure, or very little? If the rings are on right, it screams crankshaft seals. EDIT: The rings also have a bevel side that goes up. |
|
|
|
|
12-07-2014, 08:43 PM
|
#8 |
|
Not Yet Wild
Join Date: Dec 2014
Posts: 8
|
Re: 1986 ezgo will not start
rings line up with notches , bevel side up. blows good pressure , but with fuel pump off and hole open sucks good , if I put my finger on hole no suction
Thanks for the help. |
|
|
|
|
12-07-2014, 08:49 PM
|
#9 |
|
Test before replacing
Join Date: Aug 2013
Location: Ohio side of the Pennsylvania border.
Posts: 3,495
|
Re: 1986 ezgo will not start
I'm sticking with crankshaft seals.
|
|
|
|
|
12-07-2014, 08:51 PM
|
#10 |
|
Not Yet Wild
Join Date: Dec 2014
Posts: 8
|
Re: 1986 ezgo will not start
is there any tested I could do before I pull engine again ?
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| 1986 EZGO Gas | Golf Carts and Parts | |||
| 1986 gas ezgo need help | Gas EZGO | |||
| 1986 EZGO Marathon Gas - Won't Start...Help | Gas EZGO | |||
| 1986 ezgo gas | Gas EZGO | |||
Linear Mode
