EZ Go Crawls + Brake light ON

mc22 · 01-13-2018, 07:20 PM

Tried to remove and reinstall no luck still in limp mode. Also, cart not pushable in nuetral with run switch pushed to tow/maintenence .... Bearing encoder anyone think?

cgtech · 01-13-2018, 08:23 PM

Encoder would not cause brake to not release when in Tow & Neutral. Or at least never has in my experience, and I been at it for a while at the Ezgo dealer.

BobBoyce · 01-14-2018, 09:47 AM

The failure of the original motor brake could have taken out the motor brake fuse. Remove the plastic cover that has the Run/Tow switch, turn it over, and look for one or two caps on plugs with 2 wires. It will not be the #1/#2/#3/#4 set, it will be the others. typically 2 red wires on one and 2 yellow wires on the other. There are fuses under those caps, a 10 amp fuse and a 7.5 Amp fuse, if they are original. The 10 Amp fuse is for the keyswitch, and the 7.5 Amp fuse is for the motor brake. You can use a 10 Amp fuse for the motor brake if you cannot find a 7.5 Amp fuse. If it only has one fuse, it is an earlier model wiring harness and the keyswitch fuse is used for the motor brake as well. Good luck.

Bob

mc22 · 01-15-2018, 11:14 AM

No luck with motorbrake... It has the old type harness and the 1 10 amp fuse is good.
After installing new motorbrake, it is making a sound I don't remember before sounds like the rear end is clicking...? - Still limping..

01-13-2018, 07:20 PM	#11
mc22 Not Yet Wild Join Date: Aug 2017 Posts: 7	Re: EZ Go Crawls + Brake light ON Tried to remove and reinstall no luck still in limp mode. Also, cart not pushable in nuetral with run switch pushed to tow/maintenence .... Bearing encoder anyone think?
mc22 Not Yet Wild Join Date: Aug 2017 Posts: 7

01-13-2018, 08:23 PM	#12
cgtech Over This Interview Is... Join Date: Jun 2012 Location: AZ Posts: 17,449	Re: EZ Go Crawls + Brake light ON Encoder would not cause brake to not release when in Tow & Neutral. Or at least never has in my experience, and I been at it for a while at the Ezgo dealer.

01-14-2018, 09:47 AM	#13
BobBoyce Gone Insane Join Date: Oct 2015 Location: TN/NC/GA Tri-state area Posts: 3,952	Re: EZ Go Crawls + Brake light ON The failure of the original motor brake could have taken out the motor brake fuse. Remove the plastic cover that has the Run/Tow switch, turn it over, and look for one or two caps on plugs with 2 wires. It will not be the #1/#2/#3/#4 set, it will be the others. typically 2 red wires on one and 2 yellow wires on the other. There are fuses under those caps, a 10 amp fuse and a 7.5 Amp fuse, if they are original. The 10 Amp fuse is for the keyswitch, and the 7.5 Amp fuse is for the motor brake. You can use a 10 Amp fuse for the motor brake if you cannot find a 7.5 Amp fuse. If it only has one fuse, it is an earlier model wiring harness and the keyswitch fuse is used for the motor brake as well. Good luck. Bob

01-15-2018, 11:14 AM	#14
mc22 Not Yet Wild Join Date: Aug 2017 Posts: 7	Re: EZ Go Crawls + Brake light ON No luck with motorbrake... It has the old type harness and the 1 10 amp fuse is good. After installing new motorbrake, it is making a sound I don't remember before sounds like the rear end is clicking...? - Still limping..
mc22 Not Yet Wild Join Date: Aug 2017 Posts: 7

Similar Threads
Thread	Forum
Deluxe light kit question: Not getting 12v Constant to brake switch / brake wire	Electric Club Car
Tail Light / Brake Light	Electric Club Car
2012 Club Car brake light switch under brake pedal pad	Electric Club Car
rxv crawls at full throttle	Electric EZGO
Ultimate light Kit Upgrade Brake light issue	Electric Club Car

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum