07-05-2019, 08:17 AM | #21 |
Nincompoop village idiot
Join Date: Apr 2018
Location: Michigan
Posts: 9,690
|
Re: John's Cart
I would recommend a NGK plug. After many years of working on stuff, NGK or Denso are the only plugs I will use. I use nothing but NGK in small engines.
And nothing wrong with rattle bombs. I've had some really nice rattle can paint jobs, it's all in how you prep and how much time and care you take while doing it! |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-05-2019, 08:53 AM | #22 |
Gone Wild
Join Date: Dec 2015
Location: Alabama
Posts: 226
|
Re: John's Cart
You have a nice restore going on here. The finished project should be awesome. Keep up the great work.
|
07-05-2019, 11:19 AM | #23 | |
Nincompoop Club Member
Join Date: Jun 2016
Location: Idaho
Posts: 1,178
|
Re: John's Cart
Quote:
Since you're using the same crank and no shims you should be fine...... My buggy was actually 32 years old before the rebuild. It's been about 2 years ago now and it's still running strong, I golf almost everyday so it's got a lot of miles on it....... Get it back together right and yours should run for many many years too, Good Luck |
|
07-05-2019, 10:37 PM | #24 | |
Getting Wild
Join Date: Mar 2011
Location: Kingsport, TN
Posts: 89
|
Re: John's Cart
Quote:
Thanks! It's definitely not as nice as some of the other members on here but hopefully it'll be a little more respectable around the neighborhood |
|
07-05-2019, 10:39 PM | #25 | |
Getting Wild
Join Date: Mar 2011
Location: Kingsport, TN
Posts: 89
|
Re: John's Cart
Quote:
|
|
07-05-2019, 10:50 PM | #26 |
Getting Wild
Join Date: Mar 2011
Location: Kingsport, TN
Posts: 89
|
Re: John's Cart
So, what did I do today? Well, I primed another back support piece. I guess that's progress
The big thing though was prepping for the engine to go back together. I went and hosed down the other half of the crankcase and got it nice and clean. Then as I was going through what I would need I remembered that I had a head bolt that broke. Not the bolt itself but the large head piece that goes on it. So I fired up the Vulcan and made sure it stayed together I've been working graveyard the last two nights and I've been bored. Like beyond bored. Counting the ceiling tiles bored. I did watch some educational YouTube videos about TIG welding though. So tonight I decided that I'm going to pack a project. So I grabbed my tools, gaskets, seals and engine components and took off. We're taking some market downtime so I'm doing nothing but making sure the place doesn't catch fire. Normally I'm pretty busy at work. Sorry for the level of detail but I don't want you guys thinking I'm some lazy bum and I freeload |
07-05-2019, 11:03 PM | #27 |
Getting Wild
Join Date: Mar 2011
Location: Kingsport, TN
Posts: 89
|
Re: John's Cart
Once I got to work I laid it all out. Fortunately, there was a table and some cardboard for me to use. No sense explaining to the boss how I gouged up his conference room table
Following the directions on the Permatex I laid out some mighty fine beads of sealant. At this point I figured everything was going too smooth. I positioned the two cases and started pecking with my hammer. The way the bearings went on the shaft I figured this dude was just slap together. That was a big NO! The bolts were literally 1/4" too short. Better check with maintenance This was almost fruitless. However, we found some all-thread nearby that might just fit the bill 8mm with a 1.25 pitch... giggity giggity. The portaband made short work of that and we're back in action So I threaded those down in the lower case half and just bounced back and forth slowly drawing the cases closer together. Once I got about 1/4" from touching I took my all thread bits out and ran the bolts in. Since there were five of them I ran a star pattern on tightening until I got them down and within spec. Next the cylinder was nasty. I took it and the head into the other room and laid the Simple Green to it. I brought some brushes and cleaning tools so I did my best to get them as clean as I could. Once they were satisfactory I went back to the table and continued with assembly... |
07-05-2019, 11:16 PM | #28 |
Getting Wild
Join Date: Mar 2011
Location: Kingsport, TN
Posts: 89
|
Re: John's Cart
Last thing I did was install the new seals. I'll be honest I bought these from a vendor here. I kind of expected a snugger fit. I could almost press these in by hand (finger). If I bared down harder I probably could have. Whatever, they're in there now. Time will tell.....
I then cleaned the pulsar off. Not sure if I posted that picture before. Regardless, I'll post it again. I got that cleaned up and reinstalled. I tell you what that little rubber grommet that the wires run through is a PITA. Especially, when you're trying to be gentle with a 30+ piece of rubber Once I got it on I put the flywheel back on and that's where this adventure ends. I was hoping it would last most of the night but looks like I work too fast. Guess I'll have to kill five more hours somehow The good news is that I'm off tomorrow so I can get back to painting... Or maybe I'll... no... maybe I could... no... yeah I'm gonna be painting |
07-05-2019, 11:34 PM | #29 |
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: John's Cart
|
07-06-2019, 05:34 AM | #30 |
Test before replacing
Join Date: Aug 2013
Location: Ohio side of the Pennsylvania border.
Posts: 3,496
|
Re: John's Cart
The seals need loctite and should be staked in three places, or they will pop out.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
John's 1990 restoration troubles... | Gas EZGO |