|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
01-11-2020, 08:10 PM | #11 | |
Gone Wild
Join Date: Aug 2016
Location: GA
Posts: 352
|
Re: Ugh... where do I start ???
Quote:
OE F/R lever is probably why the rocker switch box isnt mounted and is just hanging there with extra wires. |
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
01-11-2020, 08:19 PM | #12 |
Gone Wild
Join Date: Aug 2016
Location: GA
Posts: 352
|
Re: Ugh... where do I start ???
Anyone aware of a schematic for this system ? or is this all cobbled together, aftermarket stuff ?
|
01-11-2020, 08:22 PM | #13 |
Bonafide Nincompoop
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 8,987
|
Re: Ugh... where do I start ???
I see a couple screw holes there but guessing they weren’t put there for the FnR switch case.
I forget what thread size the screws are that hold that box on, but they’re just in a triangle pattern. Easy to make a template, line it up, drill some holes and attach it to the body. How many wires are there? Only need three. |
01-11-2020, 08:29 PM | #14 |
Bonafide Nincompoop
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 8,987
|
Re: Ugh... where do I start ???
Depends if they used a harness for a DS or for a Precedent.
This should be close |
01-12-2020, 10:34 AM | #15 |
Gone Wild
Join Date: Aug 2016
Location: GA
Posts: 352
|
Re: Ugh... where do I start ???
|
01-12-2020, 04:37 PM | #16 |
Gone Wild
Join Date: Aug 2016
Location: GA
Posts: 352
|
Re: Ugh... where do I start ???
Made progress today.
Looks like someone mickey moused a harness for the sepex setup, but left all the old harness too. The speed sensor wasnt even on the motor... just hanging underneath. Looked like a complete mess... so I gutted all but what was connected between the Mcor and controller. Ill make a nice mounting plate for the controller and solenoid tomorrow... so its easier to access and route wires. May grab batteries this week or next weekend if I can find a set of Trojans locally. Also confirmed its a 500a controller. |
01-12-2020, 05:20 PM | #17 |
Gone Wild
Join Date: Aug 2016
Location: GA
Posts: 352
|
Re: Ugh... where do I start ???
Should I replace the Mcor while im at it ?
If so... which one do I need ??? |
01-13-2020, 07:26 AM | #18 |
Gone Wild
Join Date: Sep 2012
Location: Charlotte, NC
Posts: 9,329
|
Re: Ugh... where do I start ???
That original picture #2 You posted showing the Controller indicates that it is probably trashed.
Notice how some genius figured a way to convert the IQ harness 16-pin connector to the Curtis 24 pin receptacle by just shoveling it in the center pins. You need to try to find a 16-pin male to a 24-pin female + 6-pin female harness conversion for that Controller. It may also require installing a walkaway relay and adding a new negative to the speed sensor. |
01-13-2020, 09:36 AM | #19 | |
Gone Wild
Join Date: Aug 2016
Location: GA
Posts: 352
|
Re: Ugh... where do I start ???
Quote:
Well... I also have a fallback option to use stock parts I was given awhile back. Not sure what they are from but I know they ran off an Mcor pedal arrangement. I also dont have any reason to believe this Sepex setup was ever powered up. It was a project that was never completed... so im hoping its all still good. |
|
01-13-2020, 05:59 PM | #20 |
revolutiongolfcars.com
Join Date: Mar 2010
Location: Golf Car Capital of The World... Augusta, Georgia
Posts: 10,224
|
Re: Ugh... where do I start ???
I agree with Sergio on this one. If you're gonna try and use that 1268, you need to get the correct "conversion" harness to go from the IQ harness to the 1268 connector, which incorporates a walkaway relay as well. It also needs to have a Tow/Run switch in the circuit, which I don't know why it wouldn't already if they've put an IQ harness on the car. Maybe they've taken the Regen 1 harness that was on the car and put an IQ connector on the end of it and hoped for the best? The most headache free way to do this would be to order a new IQ wire harness for that car, with a new MCOR 4 conversion kit. Then you'll have the option of either installing the conversion harness to use the 1268, or plugging it directly into the 1510 controller you posted the picture of.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
How do I wire start and run with a key instead of pedal start/stop | Gas Club Car | |||
2017 Club Car Precedent with EFI motor - hard start/difficult start. | Gas Club Car | |||
Factory pedal start with recoil start clone | Clone Engine Swaps | |||
Gas club car solenoid click no start(Key start) | Gas Club Car | |||
whats the difference between a key start and pedal start fe350ccw? | Gas Club Car |