controller matching up

paul palmer · 09-17-2010, 01:28 PM

got this cart with no controller 1996 , 48 volts . Need help with matching up a controller with moderate use. Curtis or altrac, new or rebuilt

shadowman · 09-17-2010, 02:20 PM

whatever you do don,t go with the original it more than likely was the black one and was and still is junk, i would go with an alltrax i think but lets see what a few others think.......................................

OLD MEC · 09-17-2010, 02:27 PM

Need more info give following when asking forum for help--
Make Club Car?, year 1996, Complete serial number from frame under passenger glove box, Voltage 48 volt, type of motor?? Options below
#1- lever type control for F&R under right leg ( series )
#2- rocker type switch mounted on black box under right leg ( Regen )
Type of pedal control possible OPTIONS Below ( gives clues to controller input 0-5 ohms or 5-0 ohms )
#1- V Glide pie shaped unit under drivers seat, between batterys W/ electronic small resistors mounted on back side
#2-Obsolete potentiometer unit under drivers floor attached directly to pedal cross shaft
#3- possible conversion to MCOR under passenger floor
#4- Curtis PB-6 unit mounted in many locations but hooked to pedal linkage
With serial number and confirmation of pedal control forum should be able to get you needed info
This will seem like alot but very needed to pin down controller when there is nothing to compare to by part numbers, or shape of unit, etc.

09-17-2010, 01:28 PM	#1
paul palmer Not Yet Wild Join Date: Sep 2010 Posts: 12	controller matching up got this cart with no controller 1996 , 48 volts . Need help with matching up a controller with moderate use. Curtis or altrac, new or rebuilt
paul palmer Not Yet Wild Join Date: Sep 2010 Posts: 12

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
a DC motor controller ( electronic speed controller)	Golf Carts and Parts
Mixing and matching batteries???	Electric EZGO
pics of matching roof	Electric Club Car
Did lift kit cause controller to die? What are controller options? 95 EZGO 25864G05	Electric EZGO
Matching Motor to Controllers	Electric Club Car

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

09-17-2010, 02:20 PM	#2
shadowman The Last Moja Morani Join Date: Jan 2007 Location: jumping from cart to cart Posts: 8,975	Re: controller matching up whatever you do don,t go with the original it more than likely was the black one and was and still is junk, i would go with an alltrax i think but lets see what a few others think.......................................

09-17-2010, 02:27 PM	#3
OLD MEC Gone Wild Join Date: Mar 2009 Location: South Texas Posts: 2,391	Re: controller matching up Need more info give following when asking forum for help-- Make Club Car?, year 1996, Complete serial number from frame under passenger glove box, Voltage 48 volt, type of motor?? Options below #1- lever type control for F&R under right leg ( series ) #2- rocker type switch mounted on black box under right leg ( Regen ) Type of pedal control possible OPTIONS Below ( gives clues to controller input 0-5 ohms or 5-0 ohms ) #1- V Glide pie shaped unit under drivers seat, between batterys W/ electronic small resistors mounted on back side #2-Obsolete potentiometer unit under drivers floor attached directly to pedal cross shaft #3- possible conversion to MCOR under passenger floor #4- Curtis PB-6 unit mounted in many locations but hooked to pedal linkage With serial number and confirmation of pedal control forum should be able to get you needed info This will seem like alot but very needed to pin down controller when there is nothing to compare to by part numbers, or shape of unit, etc.