|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
01-29-2013, 11:09 AM | #11 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 98 ezgo WIDE OPEN ONLY
There appears to be some miscommunication going on here.
In his first post, BACKWOODS identified his cart as a "1998 EZGO DCS WITH 500 ALLTRAX CONTROLLER." That would mean he has Alltrax DCX500. I suspect the ITS test voltages given are for an AXE because it says to measure between pins 2 & 3. The ITS sensor is connected to pins 1 & 2 on a DCX. Are the ITS voltages the same for an AXE and a DCX, but just on a different pair of pins? |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-17-2013, 12:06 PM | #12 |
Not Yet Wild
Join Date: Oct 2009
Posts: 10
|
Re: 98 ezgo WIDE OPEN ONLY
UPDATE:
I got around to testing today.1st off cart does not move now only solenoid clicks.Battery packs measure 37.6 volts.Test pin1 to pin 2 (black to white) shows 11.45 peddle up and peddle down solenoid clicks no change 11.45 volts. Turn key on controller shows 4 green flashes followed by 6 red flashes then solid green. What should I check next? |
02-17-2013, 01:03 PM | #13 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 98 ezgo WIDE OPEN ONLY
Here is what Scotty posted for the ITS checkout for an Alltrax controller
Alltrax ITS throttle signal test: Test pin #2 to Pin #3 Peddle up reading should be 10v down should be 6v 12v = bad ITS 14v = Open circuit. On a DCX the pins are 1 & 2, but the voltages should be as stated. The 11.5V is out of range, so I'd take a really close look at the ITS wiring and sensor. |
02-17-2013, 02:40 PM | #14 | |
Not Yet Wild
Join Date: Oct 2009
Posts: 10
|
Re: 98 ezgo WIDE OPEN ONLY
Quote:
diagram shows 1 and 2 as its checked 2 and 3 and come up with 36.6 |
|
02-17-2013, 03:59 PM | #15 |
Not Yet Wild
Join Date: Oct 2009
Posts: 10
|
Re: 98 ezgo WIDE OPEN ONLY
OK AFTER FURTHER CHECKING OPENED up ITS box.
FOUND THAT SOMEHOW BLACK WIRE HAD FALLEN IN FRONT OF PLUNGER AND WAS NEARLY CUT IN HALF.PUTCRIMPED WIRE TOGRTHER AND NOW SEE 12.19 VOLTS BUT STILL NO MOVEMENT.There was some water present in box with a little corrosion starting around big head side of plunger near switch.Plunger itself was still shiny. |
02-17-2013, 04:22 PM | #16 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 98 ezgo WIDE OPEN ONLY
Quote:
What you are measuring between 2 & 3 on a DCX is one side of the ITS coil and the negative side of the Reverse Beeper, so the measurement is essentially meaningless and serves no viable purpose. |
|
02-17-2013, 04:29 PM | #17 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 98 ezgo WIDE OPEN ONLY
Quote:
The corrosion you describe should be cleaned off before it migrates into the microswitch, but it probably isn't causing any problems at the present. |
|
02-17-2013, 04:31 PM | #18 | |
Not Yet Wild
Join Date: Oct 2009
Posts: 10
|
Re: 98 ezgo WIDE OPEN ONLY
Quote:
|
|
02-17-2013, 04:41 PM | #19 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 98 ezgo WIDE OPEN ONLY
I don't know how the controller reacts when the ITS voltage between Pins 1 & 2 is out of range.
Give Alltrax a call and ask them. |
02-17-2013, 05:10 PM | #20 |
Not Yet Wild
Join Date: Oct 2009
Posts: 10
|
Re: 98 ezgo WIDE OPEN ONLY
|
|
|
Similar Threads | ||||
Thread | Forum | |||
car keeps cutting out when wide open | Gas Club Car | |||
G-16 sputter until wide open | Gas Yamaha | |||
97 Series Ezgo TXT 48v conv ITS: throttle jumps to wide open | Electric EZGO | |||
Wide Open Or Stop!! | Electric Yamaha | |||
'89 EZGO elec-Wide open or off | Electric EZGO |