|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
08-08-2016, 08:45 PM | #21 |
Gone Wild
Join Date: Mar 2016
Location: Owasso, OK
Posts: 190
|
Re: G16 loud rear end
yes it had water in it when i pulled the sight plug there was surface water that came out first and the gear oil was grey in color. i have cleaned it fully cannot see any wear on any teeth and started re assembly. Circlip behind secondary is bent slightly and i think that was my clicking noise as there is scrape marks on back of it (I will replace with the spacer) as for primary it is now cleaned and will finish taking it apart in the morning single flat spot on each roller but not seeing damage to weights they look to be newer I will post pictures once i get it apart.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-09-2016, 02:01 PM | #22 |
Gone Wild
Join Date: Mar 2016
Location: Owasso, OK
Posts: 190
|
Re: G16 loud rear end
Cgtech here is clutch.
|
08-09-2016, 02:02 PM | #23 |
Gone Wild
Join Date: Mar 2016
Location: Owasso, OK
Posts: 190
|
Re: G16 loud rear end
Will only allow 1 at a time
|
08-09-2016, 02:21 PM | #24 |
Gone Wild
Join Date: Mar 2016
Location: Owasso, OK
Posts: 190
|
Re: G16 loud rear end
Other
|
08-10-2016, 06:00 AM | #25 |
G8 Specialist
Join Date: Jun 2009
Location: Phoenix
Posts: 7,799
|
Re: G16 loud rear end
|
08-10-2016, 01:51 PM | #26 |
VC 460 CLONE GONE WILD
Join Date: Oct 2014
Location: Ray BY The Bay NJ
Posts: 10,633
|
Re: G16 loud rear end
I would also think you need to find how water got in there. Gear oil and water not a good mix.
|
08-10-2016, 04:05 PM | #27 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,314
|
Re: G16 loud rear end
A bad input shaft bearing and seal will let water in. I just replaced this one...
And this one had a loud growl... |
08-10-2016, 10:53 PM | #28 |
G8 Specialist
Join Date: Jun 2009
Location: Phoenix
Posts: 7,799
|
Re: G16 loud rear end
Wow Dave, I'd put that back in!! Good enough for Spot!!...
|
08-11-2016, 12:56 AM | #29 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: G16 loud rear end
that, loud? nah.
|
08-11-2016, 12:04 PM | #30 |
Gone Wild
Join Date: Mar 2016
Location: Owasso, OK
Posts: 190
|
Re: G16 loud rear end
I called Don yesterday and he recommended that I change both clutches out as the front has wear from belt where they have slight groove from belt riding in same position. he said I could rebuild it but may do the same in a year to 2 years which i may do instead of spending the $700 on clutches. the noise in rear end was caused by the Circlip digging in to back of the sheave which in the video it was touching the case. so I do need the spacer. and belts also I checked all mounts and found the engine lifts on front 1/8" so I will be doing motor mounts aswell and the others are good. as for the water im not sure how it went in I will check the imput shaft again but it looked good and no play in it I did notice the bottom of rear diff cover was bent a little by dragging on things and had separated enough to put a screwdriver into.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Rear end banging loud with 25 Inch tires on 6 in lift | Electric EZGO | |||
Loud pop in rear end now no go! | Electric EZGO | |||
'07 Par Car Loud Whine from rear | Columbia ParCar | |||
95 club 48v Loud Rear Noise | Electric Club Car | |||
G2 loud rear axle | Gas Yamaha |