|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
05-29-2016, 09:11 AM
|
#1 |
|
Gone Wild
Join Date: Jul 2012
Location: Mass.
Posts: 417
|
Coil on g16
My new cart stops running when she gets hot. Let it sit I will start right up. I been reading up on replacing it. Pull air box and gas tank. I'm going to clean carb and replace all fuel and vacuum lines. I will order a spair main jet just in case and a bowl seal and the 3 carb seals. And my king pins have a lot of play to I will try to grease them 1st. Plus I'm order a Yamaha coil no after market one.
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
05-29-2016, 10:43 AM
|
#2 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Coil on g16
yep
|
|
|
|
|
05-29-2016, 12:43 PM
|
#3 |
|
Gone Wild
Join Date: Jul 2012
Location: Mass.
Posts: 417
|
Re: Coil on g16
Chtech what other parts I need for king pins besides king pins. Thanks
|
|
|
|
|
05-29-2016, 12:57 PM
|
#4 |
|
maintaining a low profile
 Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,314
|
Re: Coil on g16
I've seen the king pins and bushings sold as a set.
|
|
|
|
|
05-29-2016, 01:28 PM
|
#5 |
|
Gone Wild
Join Date: Jul 2012
Location: Mass.
Posts: 417
|
Re: Coil on g16
Place I'm getting my coil selling the the king pins and bushing separate. There are Yamaha parts. I will just get a kit thanks.
|
|
|
|
|
05-30-2016, 08:23 AM
|
#6 |
|
G8 Specialist
Join Date: Jun 2009
Location: Phoenix
Posts: 7,799
|
Re: Coil on g16
Jets are over priced, and easy to clean. I'd skip the new jet!!
|
|
|
|
|
05-30-2016, 10:21 AM
|
#7 |
|
Gone Wild
Join Date: Jul 2012
Location: Mass.
Posts: 417
|
Re: Coil on g16
Ok your right the are easy to clean they are made of brass.
|
|
|
|
|
05-30-2016, 04:07 PM
|
#8 |
|
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Coil on g16
the kingpin itself is usually fine (its very hard metal). the bushings are usually bad (& sometimes plastic), the metal ones are the only ones to use & should come with blue caps to cover the upper bushings. its about a 20 minute job to replace them.
|
|
|
|
|
05-30-2016, 04:16 PM
|
#9 |
|
G8 Specialist
Join Date: Jun 2009
Location: Phoenix
Posts: 7,799
|
Re: Coil on g16
That's 20 min on an Arizona car!!
  ... |
|
|
|
|
05-30-2016, 05:03 PM
|
#10 |
|
Gone Wild
Join Date: Jul 2012
Location: Mass.
Posts: 417
|
Re: Coil on g16
Should I use King pins and bushing from Yamaha.
|
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| What would look cool? | Electric Yamaha | |||
| Cool | Test Post | |||
Linear Mode
