|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
01-18-2011, 03:52 AM | #1 |
Gone Wild
Join Date: Jan 2011
Location: Land of Oz
Posts: 192
|
1990 Marathon Govenor Adjustment
I recently purchased my first golf cart, a 1990 Marathon with the 2 stroke 3 pg gas engine. I love this site and I have already spent incredibly too much time checking out all the cool rides and gathering ideas! So far I have followed others advice and removed the oil injector and mix my gas. I have also installed the HEI conversion with great results. I am considering adjusting or removing the govenor and wanted to get your guy's opinions. I have tried to find a thread on this particular engine but so far haven't been successful. I found the one for the 85 model, but on my cart the drive belt runs from front to back, not side to side. Probably basically the same govenor adjustments but wanted to see what everyone had to say before I started tinkering. Advice on whether I should remove, adjust, or just leave it alone will be appreciated!
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
01-18-2011, 07:33 AM | #2 |
Gone Wild
Join Date: Jun 2008
Location: Raytown, Missouri
Posts: 894
|
Re: 1990 Marathon Govenor Adjustment
Welcome to BGW BadApple,If it was mine I would leave the governor on, lot better on the motor, not sure how to adjust on 2 stroke,
|
01-18-2011, 08:12 AM | #3 |
Getting Wild
Join Date: Oct 2010
Location: Glendale, AZ
Posts: 144
|
Re: 1990 Marathon Govenor Adjustment
If you do decide to pull it, there was someone about a week ago looking for govenor parts to put back on his cart.
http://www.buggiesgonewild.com/gas-e...one-parts.html |
01-18-2011, 08:47 AM | #4 |
Respect the Cart
Join Date: May 2010
Location: Rocky Mount, Virginia
Posts: 2,190
|
Re: 1990 Marathon Govenor Adjustment
Hello Bad Apple, welcome to the forum. The answer to your question really depends on how you are going to use your cart. For me the only drivers are myself and my good lady and we are both sensible people who understand that there is more than one throttle setting. So I removed the whole device as being surplus to requirements. I did, however, buy a cheapy rev counter for about $12 to keep an eye on engine speed.
That said if my cart was to be used by kids, friends and assorted drunks you can bet your life I would be protecting my investment with a governor and that little sucka would be set to 10 mph. Dave |
01-18-2011, 09:53 AM | #5 |
no clue
Join Date: Sep 2009
Location: spicewood, texas
Posts: 3,308
|
Re: 1990 Marathon Govenor Adjustment
i just tightened up the nut on the gov. a bit and left everything attached.
kids will driving it so didn't want it gone totally. |
01-18-2011, 08:27 PM | #6 |
Gone Wild
Join Date: Jan 2011
Location: Land of Oz
Posts: 192
|
Re: 1990 Marathon Govenor Adjustment
Thanks for the responses guys. I think I'm going to leave the govenor assembly hooked up and just try some minor adjustments for now. I don't plan on anyone else driving the cart but I'm sure at some point it will happen. I'm not where I can look at the cart right now, but it sounds like there will be a nut that can be adjusted either near the carb. or the clutch??? I appreciate the help.
|
01-18-2011, 08:47 PM | #7 |
Gone Wild
Join Date: Oct 2010
Location: Lawrenceburg Ky.
Posts: 1,771
|
Re: 1990 Marathon Govenor Adjustment
Welcome!
You can adjust your governor but I would keep a close on my RPMS .45ACP because shooting twice is silly. |
01-19-2011, 07:42 AM | #8 |
no clue
Join Date: Sep 2009
Location: spicewood, texas
Posts: 3,308
|
Re: 1990 Marathon Govenor Adjustment
theres a nut and spring assembly on top of the diff. just tighten it.
|
01-19-2011, 08:30 AM | #9 |
Hammer Down !!!!
Join Date: Jun 2010
Location: Lake Geneva, WI
Posts: 2,681
|
Re: 1990 Marathon Govenor Adjustment
do yourself a favor and buy a cheap tach off of Ebay either way (should run under about $15 shipped) - it's always a good idea to watch your RPM's as these little 2-strokes love to overrev (5k is the factory recommended limit, I have my governor set around 4400 and even on hills, etc it never goes over 4800, but you'd never know as the cart will still do 20+ with 2 people).
|
01-19-2011, 07:52 PM | #10 |
Gone Wild
Join Date: Jan 2011
Location: Land of Oz
Posts: 192
|
Re: 1990 Marathon Govenor Adjustment
Thanks for all the advice. I will get a tach ordered and then do a little adjusting on the govenor.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
1990 Club car With flat head Rev limiter question and govenor question | Gas Club Car | |||
Need engine for 1990 ez go marathon | Golf Carts and Parts | |||
G16 govenor nut adjustment | Gas Yamaha | |||
help adjusting govenor on ezgo marathon (yr.85) | Gas EZGO | |||
How to take 1990 Marathon from 36v to 48v? | Electric EZGO |