|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
|
05-03-2017, 10:38 AM | #1 |
Getting Wild
Join Date: Nov 2015
Location: Dayton, Ohio
Posts: 134
|
Hesitation with a newly installed XCT400PDS controller
I just bought a xct400PDS controller/solenoid off of scottyB and installed it in my pre2001 EZGO PDS 36volt cart. When I push on the gas pedal the cart doesn't move right away ( maybe a second or 2 hesitation) I'm not sure if this is normal or a setting that I can change in the programming (Does it in turf or street modes) or if it's maybe something with the stock motor. Didn't seem to do this (that I can remember at least) with the old stock controller.
Is there anyone else using this controller that is experiencing this? |
05-03-2017, 12:46 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Hesitation with a newly installed XCT400PDS controller
Did you try increasing the throttle ramp rate yet?
|
05-03-2017, 01:33 PM | #3 |
Getting Wild
Join Date: Nov 2015
Location: Dayton, Ohio
Posts: 134
|
Re: Hesitation with a newly installed XCT400PDS controller
I haven't tried that yet, I'm going to mess with it some this weekend if the weather isn't to bad. I'm honestly thinking that this may be normal with this controller or maybe it's caused by the stock motor. I'll let you know if I figure anything out when I mess with it this weekend.
|
05-03-2017, 01:38 PM | #4 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Hesitation with a newly installed XCT400PDS controller
Take notice if the solenoid is slow to click or if the solenoid clicks and then the pedal has to move down much more before the cart moves.
Do this and report back to me BEFORE you start messing with the settings |
05-07-2017, 11:08 AM | #5 | |
Getting Wild
Join Date: Nov 2015
Location: Dayton, Ohio
Posts: 134
|
Re: Hesitation with a newly installed XCT400PDS controller
Quote:
I'm also going to check that % value on the double sided arrow that you mentioned in the above post. I'll let you know what I find out. |
|
05-03-2017, 12:59 PM | #6 | |
Getting Wild
Join Date: Aug 2016
Posts: 90
|
Re: Hesitation with a newly installed XCT400PDS controller
Quote:
|
|
05-03-2017, 01:40 PM | #7 |
Getting Wild
Join Date: Nov 2015
Location: Dayton, Ohio
Posts: 134
|
Re: Hesitation with a newly installed XCT400PDS controller
That's what I'm kinda thinking also but wanted to see if it was the same for other people. I'm going to play with some settings to see if I can't make it any better.
|
05-03-2017, 01:41 PM | #8 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Hesitation with a newly installed XCT400PDS controller
See post #5
|
05-03-2017, 06:45 PM | #9 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Hesitation with a newly installed XCT400PDS controller
Well, if you are gonna throw caution to the wind, at least save (or write down) the original values of stuff before you change it. That way if you make it worse, you can go back to where you started.
|
05-03-2017, 07:56 PM | #10 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Hesitation with a newly installed XCT400PDS controller
LOL amen to that
|
|
|
Similar Threads | ||||
Thread | Forum | |||
New xct400pds | Electric EZGO | |||
Upgraded XCT400PDS and cart are lifeless | Electric EZGO | |||
Newly installed rebuilt eh 292 robins eng. w/ no pressure to the fuel pump? | Gas EZGO | |||
Installed New Controller | Electric EZGO | |||
Newly installed lift on Hunting Buggie | Lifted Golf Carts |