|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
06-02-2019, 03:30 PM | #11 |
Gone Wild
Join Date: Feb 2019
Location: God's Country America
Posts: 883
|
Re: EZ-GO 2008 RXV openCAN not sending info
It is GEN3. By EDT.LLC trade mark Energy Design Tek LLC
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-02-2019, 03:50 PM | #12 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: EZ-GO 2008 RXV openCAN not sending info
Thanks. I like the all black better. Here's mine.
I went to their website and downloaded their Gen3 manual. It still uses a user installed motor temperature sensor, a user installed speed sensor, that counts pulses. One pulse per revolution, so you enter tire circumference, optional external power only says use a key switched power source from 12 to 48 volts. I made sure I downloaded the Gen 3 manual, but they may have something specific to RXVs. I'd think speed would be easier if it came from the controller. One less sensor to install and that may go bad. Dunno if RXV motors have a temp sensor inside the stator windings, but if they do, that would be superior to an externally mounted temp sensor. Voltage can pretty much come from anywhere, though they recommend key switched. Mine is connector to a 10 position rotary switch that's off, pack, batteries 1 - 8, aux battery. |
06-02-2019, 03:57 PM | #13 |
Gone Wild
Join Date: Feb 2019
Location: God's Country America
Posts: 883
|
Re: EZ-GO 2008 RXV openCAN not sending info
Yurtle did u see my post that include 2 pictures and wiring instructions for rxvs?
The question is can I tap the blk/white and red? |
06-02-2019, 03:59 PM | #14 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: EZ-GO 2008 RXV openCAN not sending info
|
06-02-2019, 04:13 PM | #15 |
Gone Insane
Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
|
Re: EZ-GO 2008 RXV openCAN not sending info
The RXV has a temperature sensor embedded in the windings. The speed encoder is dual channel 5V pulses. Phase differential shows motor spin direction, pulse rate indicates RPM.
The CAN bus signal digitally communicates SOC percentage only on the RXV by default, without being queried for it. The 2Five rotates through a number of data sequences, as it provides information to the speedometer display. The device connected identifies itself to the controller, so the controller provides the data that the device is requiring. |
06-02-2019, 05:36 PM | #16 | |
Gone Wild
Join Date: Feb 2019
Location: God's Country America
Posts: 883
|
Re: EZ-GO 2008 RXV openCAN not sending info
Quote:
So does that mean yes? And I can use the red and blk/white? |
|
06-02-2019, 05:49 PM | #17 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: EZ-GO 2008 RXV openCAN not sending info
|
06-02-2019, 05:54 PM | #18 | |
Gone Wild
Join Date: Feb 2019
Location: God's Country America
Posts: 883
|
Re: EZ-GO 2008 RXV openCAN not sending info
Quote:
Thanks I read that. Can u answer my question? |
|
06-02-2019, 06:13 PM | #19 | |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: EZ-GO 2008 RXV openCAN not sending info
Quote:
There is a difference between a reducer that pulls 10 amps, and a volt meter/clock/temp/odo/speedo, which is in the milliamps range. |
|
06-02-2019, 06:18 PM | #20 |
Gone Wild
Join Date: Feb 2019
Location: God's Country America
Posts: 883
|
Re: EZ-GO 2008 RXV openCAN not sending info
Let's keep it simple. U don't know.
|
Tags |
canalyst2, canbus, canopen, canprotocol, ezgo |
|
|
Similar Threads | ||||
Thread | Forum | |||
Sending unit | Gas Club Car | |||
2008 ezgo 2+2 swap info | Big Block Talk! | |||
Oil sending unit wire | Gas EZGO | |||
Sending it to PQ | Electric Club Car |