|
Electric Club Car Electric DS, and Precedent golf cars |
|
Thread Tools | Display Modes |
03-13-2014, 02:09 PM | #1 |
Not Yet Wild
Join Date: Mar 2014
Posts: 1
|
Wiring for LED Volt Gauge for Club CR
I bought a LED gage for my club car and need information as to how and where to run the wires from the batteries to my dashboard where I mounted the gage. How is this done? I cannot get on the ground to get under the cart. I already connected the 16-gauge wires to the batteries, but don't know how to run the wires to the front without getting under the cart. Thanks for your help if you can give me some advice. - twig
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-13-2014, 02:33 PM | #2 |
Cave Dweller
Join Date: Apr 2013
Location: Always On The Move
Posts: 22,117
|
Re: Wiring for LED Volt Gauge for Club CR
mine are run under the cart .
|
03-13-2014, 05:12 PM | #3 |
Medicare Recipient
Join Date: Jun 2011
Location: West Michigan
Posts: 3,541
|
Re: Wiring for LED Volt Gauge for Club CR
. . . flip the cart over . . .
|
03-14-2014, 06:48 AM | #4 |
Not Yet Wild
Join Date: Jan 2014
Location: Valley Grande, Alabama
Posts: 36
|
Re: Wiring for LED Volt Gauge for Club CR
I just ran all the wiring for my LEDs under the cart
|
03-14-2014, 07:26 AM | #5 |
Getting Wild
Join Date: Oct 2013
Location: Virginia Beach
Posts: 125
|
Re: Wiring for LED Volt Gauge for Club CR
If you plan on mounting the gauge in the dash then you have no choice but to run them under the cart. If you are physically unable to get on the ground and run the wires then I suggest that you find someone that can. The only other option is to mount the gauge somewhere near your F/R switch. If you do that, then I would mount it upside down so you can read it from your seat.
Good luck. Welcome to BGW. |
03-14-2014, 08:08 AM | #6 |
Gone Wild
Join Date: Jan 2014
Location: Lafayette, Louisiana
Posts: 1,677
|
Re: Wiring for LED Volt Gauge for Club CR
To read the voltage can you just tap into your switch and ground off your harness or find a 48V hot if you have one there already. I mean your drawing hardly nothing your just sampling voltage right? I don't think you have to go direct for this meter to be accurate you just need to have access to the full 48 volts right?
|
03-14-2014, 09:11 AM | #7 |
Getting Wild
Join Date: Jun 2013
Location: Sugar Land, TX
Posts: 126
|
Thumbs up for scooterman's response
Smackdaddy66 |
03-14-2014, 03:03 PM | #8 |
South LA Coonass
Join Date: Mar 2014
Location: New Iberia, LA
Posts: 531
|
Re: Wiring for LED Volt Gauge for Club CR
I just installed a voltmeter on my '92 DS and ran my wires into the factory wire holders down the frame. My meter is mounted in the plastic next to the key switch. I did a direct battery hookup.
|
07-25-2014, 08:30 PM | #9 |
Gone Wild
Join Date: Apr 2011
Location: New Jersey
Posts: 999
|
Re: Wiring for LED Volt Gauge for Club CR
I am going to hook one up on Sunday to my 48 volt cc Ds. I am going neg from led meter to neg battery and positive from meter to key switch that is hot when on. I think this is all I have to do. Any thoughts ??? Thanks
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Gas Gauge & Volt Gauge in G16...Done! | Gas Yamaha | |||
97 club car 48 volt wiring | Golf Carts and Parts | |||
1991 club car 36 volt wiring diagram | Electric Club Car | |||
Main Battery Wiring on Club 48 Volt | Electric Club Car | |||
94 club car 48 volt wiring | Electric Club Car |