|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
10-28-2021, 09:25 AM | #1 |
Not Yet Wild
Join Date: Jul 2019
Location: Seguin, TX.
Posts: 5
|
99 PDS FR Upgrade wiring Question, Hockey puck to HD
Trying to change out my Hockey puck for a Heavy Duty FR switch.
INFO: 99 PDS 36V, 6" lift, Original controller was sent in to a guy to be turned up to 400 amps, worked great for a long time and is now stopping after maybe 100 yds. of driving, seems to have very little torque. Battery indicator goes from fully charged to blinking between yellow and red when it does this yet it will go into reverse just fine and take off with lot's of power. (Brand new batteries and wires were just installed and no change) I'm not good at diagnosing electrical issues so basically I'm throwing parts at it now. I will try and upload pics of what I have as the old hockey puck has 6 wires, 2 that are not connected and the Heavy duty switch has connectors for 4 wires, 3 on one side and 1 on the other. Thank you in advance and please excuse my ignorance.. PS: I have spent several hours reading the sticky's and searching forum posts and have had no luck finding this... New FR #2.jpg Old FR Switch.jpg |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
10-28-2021, 01:08 PM | #2 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 99 PDS FR Upgrade wiring Question, Hockey puck to HD
The old F/R switch is for a sepex drive and the new F/R switch is for a series drive. The new one won't work in your cart.
Also, you are saying your cart has a PDS drive, yet the F/R switch is for a DCS drive. Attached is a picture of a F/R cam for an early 2000 PDS drive. Note there is only one raised area and there are two raised areas on the cam in the picture you posted. Take a look at the controller. If it has a 10-pin plug on top, it is a DCS. If it has five plugs on the front, it is a PDS. In either case, the F/R switch assembly can be replaced with a DPDT/center Off switch or a SPDT/center OFF with a diode. |
10-28-2021, 01:17 PM | #3 | |
Not Yet Wild
Join Date: Jul 2019
Location: Seguin, TX.
Posts: 5
|
Re: 99 PDS FR Upgrade wiring Question, Hockey puck to HD
Quote:
|
|
10-28-2021, 01:41 PM | #4 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 99 PDS FR Upgrade wiring Question, Hockey puck to HD
Go down to item #7 near bottom of page. Get the switch and housing. It fits where the direction lever is now and makes shifting between F, N and R easy.
https://www.cartsunlimited.net/f---r--switches.html |
10-28-2021, 01:44 PM | #5 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,188
|
Re: 99 PDS FR Upgrade wiring Question, Hockey puck to HD
An FnR switch and housing for a club car works well. Diagram attached
|
10-28-2021, 02:41 PM | #6 | |
Not Yet Wild
Join Date: Jul 2019
Location: Seguin, TX.
Posts: 5
|
Re: 99 PDS FR Upgrade wiring Question, Hockey puck to HD
Quote:
|
|
05-03-2022, 06:46 AM | #7 |
Not Yet Wild
Join Date: Apr 2022
Location: New York
Posts: 1
|
Re: 99 PDS FR Upgrade wiring Question, Hockey puck to HD
|
05-03-2022, 07:51 AM | #8 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,188
|
Re: 99 PDS FR Upgrade wiring Question, Hockey puck to HD
Go look here post #7 https://www.buggiesgonewild.com/showthread.php?t=183822
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Wiring Upgrade Question/Opinions | Electric Club Car | |||
Wiring upgrade question?? | Electric EZGO | |||
48 volt Upgrade question on wiring | Electric EZGO |