lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Yamaha
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles



Post New Thread  Reply
 
Thread Tools Display Modes
Old 03-02-2014, 09:06 PM   #1
donetheconversion
Getting Wild
 
donetheconversion's Avatar
Yamaha
 
Join Date: Oct 2010
Location: Holland, Michigan
Posts: 112
Default "the right stuff"

Wondering your guys thoughts on "the right stuff" to seal up a crank case. I opened up my motor and the gasket was shot after. i have "the right stuff" gasket maker, but the only thing thats holding me back is that its not gasoline resistant. Would that be a concern for this application?

anyone have any experience using this stuff?
donetheconversion is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 03-02-2014, 09:55 PM   #2
pachanga90
I Refuse To Get Stuck!!!
 
pachanga90's Avatar
E-Z-GO
 
Join Date: Jun 2010
Location: Hilton,NY
Posts: 5,424
Default Re: "the right stuff"

A lot depends on if the gasket also acts as a shim,in some cases the gasket must be a certain thickness,or it can cause binding if its a side cover for the crankcase.The Right Stuff is excellent sealer,and works good,just make sure about the application,before doing it.I always use gaskets in any type of case/housing unless otherwise specified.Unless its a 2-stroke,gas won't be a concern.Hope this helps.
pachanga90 is offline   Reply With Quote
Old 03-02-2014, 10:34 PM   #3
cgtech
Over This Interview Is...
 
cgtech's Avatar
Yamaha
 
Join Date: Jun 2012
Location: AZ
Posts: 17,441
Default Re: "the right stuff"

If you have gas in there, you need to address that carb. "right stuff" is very close to the best quality oem stuff. Yep, the "right stuff" is the right stuff, use it if you want the right stuff. It will not replace a gasket when shimming is concerned. Usually when a gasket is specified, it really does need to be there. As stated above, it all depends on the application. Anywhere "side clearence" is an issue, do it right, for valve covers, or diff covers, go for it.
cgtech is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Gas Yamaha


Thread Tools
Display Modes


Similar Threads
Thread Forum
Club Car belt/clutch won't "change", as stuck in "low" gear Gas Club Car
Why "Carbon Fiber" "Wood grain" and Diamond Plated? Gas EZGO
What kind of offset is my EZGO RXV w/Jakes 6" Lift Kit and 2" spacer rear and 1" back Lifted Golf Carts
4" lift and stuff Gas Club Car
Yamaha "Stuff" for sale Golf Carts and Parts


All times are GMT -5. The time now is 03:52 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.