|
Big Block Talk! Everything about swapping a big block engine into your cart! |
|
Thread Tools | Display Modes |
09-10-2012, 01:52 PM | #11 |
REAL MEN GET EM DIRTY
Join Date: Jun 2009
Location: rincon , ga.
Posts: 3,646
|
re: CPP 23 -- Yamaha G16
mine does also dave, we have them idealing at lower rpms than what its designed for.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-10-2012, 01:55 PM | #12 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
re: CPP 23 -- Yamaha G16
ok--cool.
|
09-10-2012, 02:29 PM | #13 |
REAL MEN GET EM DIRTY
Join Date: Jun 2009
Location: rincon , ga.
Posts: 3,646
|
re: CPP 23 -- Yamaha G16
but in reality, it shouldnt be idiling. it should be wot most all the time
|
10-01-2012, 03:42 PM | #14 |
Gone Wild
Join Date: Aug 2010
Location: Port Wentworth, GA
Posts: 247
|
re: CPP 23 -- Yamaha G16
Hey Dave, nice set-up. My 18hp from CPP has the same lag problem. My throttle cable runs from pedal to rear-end governor, then to the carb. There are so many springs in the set-up that the gas pedal must be pressed half way down before any reaction from the engine. The only solution is to bypass all of that stuff and connect the gas pedal directly to the carb. I'm planning on doing that to mine after the first of the year, along with rev kit, adv. timing key, and maybe the cam. My rear end has the magnet governor system, so I have to go into the rear end to remove the weights.
A word of advice, never ever for any reason run gas with ethanol in that engine. The ethanol destroys everything on these engines, and warranty does not cover the replacement parts. I have spent almost $200 on replacement parts to get my engine running properly again, and the only use it has seen was 2 hours at CAW. |
10-01-2012, 03:46 PM | #15 | |
Gone Wild
Join Date: Aug 2010
Location: Port Wentworth, GA
Posts: 247
|
re: CPP 23 -- Yamaha G16
Quote:
|
|
10-05-2012, 10:01 PM | #16 |
Not Yet Wild
Join Date: Jul 2008
Location: Charlotte, NC.
Posts: 49
|
re: CPP 23 -- Yamaha G16
Very nice and clean install. I can't wait to get started on mine.
|
10-06-2012, 04:18 PM | #17 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
re: CPP 23 -- Yamaha G16
|
10-06-2012, 04:25 PM | #18 |
Not your usual outlaw
Join Date: Oct 2008
Location: Near Lake Geneva, WI
Posts: 20,054
|
re: CPP 23 -- Yamaha G16
|
10-06-2012, 05:59 PM | #19 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
re: CPP 23 -- Yamaha G16
|
10-17-2012, 03:40 PM | #20 |
maintaining a low profile
Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,316
|
re: CPP 23 -- Yamaha G16
Added some bling bling...
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Wanted: Yamaha G1 rolling chassis (or any Yamaha really) | Golf Carts and Parts |