lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car
Electric Club Car Electric DS, and Precedent golf cars



Post New Thread  Reply
 
Thread Tools Display Modes
Old 05-08-2021, 01:33 PM   #1
mgray70
Gone Wild
 
mgray70's Avatar
E-Z-GO
 
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,034
Default 08 precedent XCT interlock issues

Can anyone tell me how to disable the charger interlock?
Here's the story. 08 precedent. It has as new Alltrax XCT, new wiring harness. Controller powers up, but will not engage solenoid because it is showing the charger is plugged in. Even with the OBC bypass it still shows it and has the cart disabled. How is the best way to turn the interlock off on the Alltrax?
mgray70 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 05-08-2021, 03:26 PM   #2
R&TBabich
Gone Wild
Club Car
 
Join Date: Apr 2020
Location: 1000 Oaks, SOCAL
Posts: 406
Default Re: 08 precedent XCT interlock issues

Quote:
Originally Posted by mgray70 View Post
.... How is the best way to turn the interlock off on the Alltrax?
The Charger Disable interlock is on controller pin #5 - Light Blue.
Supply +48v on that line for the cart to go.
The OBC would pull that input when charging.
You could just connect it to +48v all the time, just remember to disconnect the charger when you want to use the cart.
The White input line to the OBC is +48v from the Tow/Run switch.
When bypassing/removing the OBC the White line gets connected to the Light Blue.
Or run a new wire to the Light Blue from the Light Green of the Tow/Run switch.
R&TBabich is offline   Reply With Quote
Old 05-08-2021, 05:10 PM   #3
mgray70
Gone Wild
 
mgray70's Avatar
E-Z-GO
 
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,034
Default Re: 08 precedent XCT interlock issues

Quote:
Originally Posted by R&TBabich View Post
The Charger Disable interlock is on controller pin #5 - Light Blue.

Supply +48v on that line for the cart to go.

The OBC would pull that input when charging.

You could just connect it to +48v all the time, just remember to disconnect the charger when you want to use the cart.

The White input line to the OBC is +48v from the Tow/Run switch.

When bypassing/removing the OBC the White line gets connected to the Light Blue.

Or run a new wire to the Light Blue from the Light Green of the Tow/Run switch.
This is the oddest thing. I had done the bypass with the white and blue wires and I still get the true reading on the charger input. I can disconnect the white and blue wires and the cart will run in limp mode.
mgray70 is offline   Reply With Quote
Old 05-09-2021, 02:04 PM   #4
Fairtax4me
I gotta find a round Tuit
 
Fairtax4me's Avatar
Club Car
 
Join Date: Dec 2015
Location: Charlottesburg Va
Posts: 5,804
Default Re: 08 precedent XCT interlock issues

Can you use the Alltrax toolkit and disable charger interlock altogether?
Seems like the Alltrax is seeing 48V as the signal to disable.
Fairtax4me is online now   Reply With Quote
Old 05-10-2021, 07:28 AM   #5
mgray70
Gone Wild
 
mgray70's Avatar
E-Z-GO
 
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,034
Default Re: 08 precedent XCT interlock issues

Quote:
Originally Posted by Fairtax4me View Post
Can you use the Alltrax toolkit and disable charger interlock altogether?

Seems like the Alltrax is seeing 48V as the signal to disable.
I looked at toolkit trying to figure out a way till I was seeing cross eyed. At one point it would run with the charger plugged in and not with it unplugged. Right now it will run with the blue and white wires cut like doing the bypass, but not connected together.
mgray70 is offline   Reply With Quote
Old 05-10-2021, 11:06 AM   #6
R&TBabich
Gone Wild
Club Car
 
Join Date: Apr 2020
Location: 1000 Oaks, SOCAL
Posts: 406
Default Re: 08 precedent XCT interlock issues

Quote:
Originally Posted by mgray70 View Post
I looked at toolkit trying to figure out a way till I was seeing cross eyed. ....
Call tech support at Alltrax about the Toolkit interlock.
I've found them to be very helpful.
R&TBabich is offline   Reply With Quote
Old 05-10-2021, 07:16 PM   #7
mgray70
Gone Wild
 
mgray70's Avatar
E-Z-GO
 
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,034
Default Re: 08 precedent XCT interlock issues

Cart runs perfectly with the blue and white wires cut from the OBC, but NOT connected to each other, and before I did that it would run with the charger plugged in, but not when unplugged. The limp mode issue I had was the wrong pole was selected on the speed sensor. I think Alltrax had some backwards programming on this one. I will e-mail Will at Alltrax to verify. Definitely an odd one.
mgray70 is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Club Car


Thread Tools
Display Modes


Similar Threads
Thread Forum
XCT 500, Lester Summit 2 and interlock Electric Club Car
DeltaQ 912 charger interlock Electric Club Car
2009 Par Car Bypass Interlock Columbia ParCar
Club car charger interlock Electric Club Car
Interlock Repair on G8 Electric Yamaha


All times are GMT -5. The time now is 05:53 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. 2006-2017 Buggiesgonewild.com. All rights reserved.