|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
06-23-2020, 08:54 PM
|
#1 |
|
Not Yet Wild
Join Date: Jun 2020
Posts: 2
|
G9/G5 no crank and cut wires?
Just bought a 94 gas, I think its a G9 (fleet). Trying to get started, no crank, noticed the wires that go to the micro switch activated by the gear selector lever have been cut. Why would someone do this? Can I bypass these? Thanks in advance. Want to get this thing started!
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
06-24-2020, 08:52 AM
|
#2 |
|
Searching for The Way
 Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,441
|
Re: G9/G5 no crank and cut wires?
Don't know why someone did it. I've seen some really butchered up carts without good reason for the butchering.
You could try to reconnect the wires. Anytime one is having electrical issues on a vehicle and there are damaged wires, the first step is to fix the wires. |
|
|
|
|
06-25-2020, 08:58 AM
|
#3 |
|
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: G9/G5 no crank and cut wires?
Those wires and micro switch would be for the back up buzzer. Has no control over the starting circuit.
|
|
|
|
|
06-26-2020, 09:07 PM
|
#4 |
|
Not Yet Wild
Join Date: Jun 2020
Posts: 2
|
Re: G9/G5 no crank and cut wires?
Ok, found the fuse, it was fried, replaced, no fire. New battery. I suspect the gas pedal switch, can someone tell me how to bypass it? I have power at the relay, at the fuse, cant get power to the starter. Tried to put tester needle all around gas pedal plunger switch, nothing. No idea what Im doing but this cant be that hard. I hate having the gas pedal start this thing. Help! I think Im close!
|
|
|
|
|
06-27-2020, 01:51 AM
|
#5 |
|
Runs with scissors-
Join Date: Dec 2010
Location: Da UP
Posts: 1,962
|
Re: G9/G5 no crank and cut wires?
smallblock450sl has forgotten more than I’ll likely ever know about Yamaha carts. Between him and slonomo & some others they’ll have this figured, and yes, sounds like you’re almost there
 |
|
|
|
|
06-27-2020, 10:35 AM
|
#6 |
|
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,875
|
Re: G9/G5 no crank and cut wires?
There is a "sticky" at the top of this section. "so your Yami wont turn over". You will need a volt meter and know how to use it. Good luck
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| I hooked up main wires to batteries backwards, fried some wires, help??? | Electric EZGO | |||
| HD rod and crank | Gas Harley Davidson | |||
| Does a 2pg have a crank case pressure pickup tube inside the crank case? (pic) | Gas EZGO | |||
| aligment of cam shaft, crank, and crank balance on g14 | Gas Yamaha | |||
| 94 EZ-GO gxt 804 will not crank | Gas EZGO | |||
Linear Mode
