Gas cc will not do anything until i jumpier across solenoid

ACONLP · 12-12-2010, 05:08 PM

Sat for about three years. Got it home. Got it running. Ran fine for about an hour. Went to go drive it for the first time, went two feet and stoped. Now cant get it to do anything unless i jumpier across the solenoid, and that just turn the motor over. The micro switch's all click. Replaced the solenoid with one from a auto parts house( which i was told would not work ). I dont know

scottyb · 12-12-2010, 07:17 PM

You can use a voltmeter or test light to diagnose the solenoid activation circuit or just replace it with the OEM solenoid.

ckiguy · 12-12-2010, 10:32 PM

just because the micros click dosent mean they are working! just like a rifle, you can get a bang with no kick! this means the bullet will get hit by the firing pin, but the bullet will not exit the casing! get a volt meter and set it to a contunity or diode test or a beep test. test with one lead one each connector. red on one, black on one. squeeze each micro. if it does the oppitite of when yo started, beep, or no beep its can be assumed a good switch. if it stays the same, assume bad switch.
all the soloiud is a heavy duty switch. that has to be energised to work. if its not receiveing the signal it will do whta is told...nothing!
like it was brought up in your previous post.

ACONLP · 12-13-2010, 07:05 PM

okay i replaced all the micro switch and still nothing. turn the starter by hand and still nothing.

scottyb · 12-13-2010, 08:18 PM

ALL the micro-switches? What about the 2 in the black box?

ACONLP · 12-13-2010, 08:21 PM

yes all four of them. i dont know were to go now

ACONLP · 12-13-2010, 10:45 PM

well just got it running. replaced all 4 micro switch's, replaced some wire terminals, PUT THE ORIGINAL SOLENOID BACK ON. It fired right off. So i think it was the switch's

scottyb · 12-13-2010, 10:52 PM

Quote:

Originally Posted by ACONLP

well just got it running. replaced all 4 micro switch's, replaced some wire terminals, PUT THE ORIGINAL SOLENOID BACK ON. It fired right off. So i think it was the switch's

...and the automotive solenoid did not work in the golf cart.

ACONLP · 12-14-2010, 12:35 AM

Quote:

Originally Posted by scottyb

...and the automotive solenoid did not work in the golf cart.

nope sure didnt... it was worth a shot. 13bucks waste, but o well..

was getting to many different answers on it, so i tried it. i look at it has i took one for the team..

rib33024 · 12-14-2010, 01:10 AM

Glad you got it running

But you lost me on this, was getting to many different answers on it ? the only thing I see talked about in this thread is the switches and the solenoid, and you say the switches were the problem

Quote:

Originally Posted by ACONLP

nope sure didnt... it was worth a shot. 13bucks waste, but o well..

was getting to many different answers on it, so i tried it. i look at it has i took one for the team..

12-12-2010, 05:08 PM	#1
ACONLP Not Yet Wild Join Date: Oct 2010 Location: Texas Posts: 15	Gas cc will not do anything until i jumpier across solenoid Sat for about three years. Got it home. Got it running. Ran fine for about an hour. Went to go drive it for the first time, went two feet and stoped. Now cant get it to do anything unless i jumpier across the solenoid, and that just turn the motor over. The micro switch's all click. Replaced the solenoid with one from a auto parts house( which i was told would not work ). I dont know

12-12-2010, 07:17 PM	#2
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,402	Re: Gas cc will not do anything until i jumpier across solenoid You can use a voltmeter or test light to diagnose the solenoid activation circuit or just replace it with the OEM solenoid.

12-12-2010, 10:32 PM	#3
ckiguy Bad *** Speller! Join Date: Oct 2009 Location: Columbus, Ohio Posts: 1,338	Re: Gas cc will not do anything until i jumpier across solenoid just because the micros click dosent mean they are working! just like a rifle, you can get a bang with no kick! this means the bullet will get hit by the firing pin, but the bullet will not exit the casing! get a volt meter and set it to a contunity or diode test or a beep test. test with one lead one each connector. red on one, black on one. squeeze each micro. if it does the oppitite of when yo started, beep, or no beep its can be assumed a good switch. if it stays the same, assume bad switch. all the soloiud is a heavy duty switch. that has to be energised to work. if its not receiveing the signal it will do whta is told...nothing! like it was brought up in your previous post.

12-13-2010, 07:05 PM	#4
ACONLP Not Yet Wild Join Date: Oct 2010 Location: Texas Posts: 15	Re: Gas cc will not do anything until i jumpier across solenoid okay i replaced all the micro switch and still nothing. turn the starter by hand and still nothing.

12-13-2010, 08:18 PM	#5
scottyb Happy Carting Join Date: Dec 2007 Location: Southern California Posts: 73,402	Re: Gas cc will not do anything until i jumpier across solenoid ALL the micro-switches? What about the 2 in the black box?

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

12-13-2010, 08:21 PM	#6
ACONLP Not Yet Wild Join Date: Oct 2010 Location: Texas Posts: 15	Re: Gas cc will not do anything until i jumpier across solenoid yes all four of them. i dont know were to go now

12-13-2010, 10:45 PM	#7
ACONLP Not Yet Wild Join Date: Oct 2010 Location: Texas Posts: 15	Re: Gas cc will not do anything until i jumpier across solenoid well just got it running. replaced all 4 micro switch's, replaced some wire terminals, PUT THE ORIGINAL SOLENOID BACK ON. It fired right off. So i think it was the switch's

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
48V solenoid on a 36V	Electric EZGO
Solenoid	Electric EZGO
Need help with new solenoid	Electric EZGO
Where is solenoid on 99 Ez Go?	Electric EZGO
98 new solenoid, still won't go	Electric EZGO