Alltrax XTC Controller Help

i.weber · 09-22-2019, 03:52 PM

Quote:

Originally Posted by scottyb

Yeah but, what about the solenoid coil

Years ago a guy connect the main + to one side of the MZJ400 solenoid and the main - to the other side. When he stepped on the gas there was an explosion under the seat as the solenoid blew the bridge through the top. The Alltrax was unharmed. More than I can say for his shorts

Mine seems fine but Scotty will have to chime in and let me know what he thinks.

Sent from my SM-G975U using Tapatalk

WalterM6 · 09-23-2019, 04:10 PM

How is your cart running Mr i. weber?

i.weber · 09-23-2019, 04:12 PM

Quote:

Originally Posted by WalterM6

How is your cart running Mr i. weber?

So far so good. Throttle is a little rough but my expectations may have been too high. What damage would you foresee taking place if the controller was hooked up incorrectly?

Sent from my SM-G975U using Tapatalk

Sergio · 09-23-2019, 04:34 PM

This is my throttle curve on a Precedent with an XCT-500, if You make the first half of the curve very gradual the cart will have a very smooth throttle at crawl-to-low speed:

Did You ever install the flyback diode on the solenoid coil?

That picture You posted for the Solenoid does not clearly show the Solenoid coil connections (or it was an old picture) and it it is hard to verify it is wired properly.

WalterM6 · 09-23-2019, 05:43 PM

Quote:

Throttle is a little rough

That may be caused by the dielectric grease that you were worried about earlier. Get a can of CRC Electric Contact Cleaner and cleanup some of the grease. You can get it at automotive stores. Also if you had your controller hooked up wrong it wouldn't run right.

i.weber · 09-26-2019, 12:20 AM

Just noticed tonight that I haven't heard my reverse buzzer since I installed the new controller. Is this common? Other than that, no other issues.

Sent from my SM-G975U using Tapatalk

Sergio · 09-26-2019, 05:36 AM

The reverse buzzer should work as before, if you wired anything behind the dash make sure the buzzer did not unplugged (put the cart on Tow before removing the dash).

How did you fix the rough throttle?

09-23-2019, 04:10 PM	#22
WalterM6 Gone Wild Join Date: Apr 2017 Location: SE TN Posts: 2,227	Re: Alltrax XTC Controller Help How is your cart running Mr i. weber?

09-23-2019, 04:34 PM	#24
Sergio Gone Wild Join Date: Sep 2012 Location: Charlotte, NC Posts: 9,329	Re: Alltrax XTC Controller Help This is my throttle curve on a Precedent with an XCT-500, if You make the first half of the curve very gradual the cart will have a very smooth throttle at crawl-to-low speed: Did You ever install the flyback diode on the solenoid coil? That picture You posted for the Solenoid does not clearly show the Solenoid coil connections (or it was an old picture) and it it is hard to verify it is wired properly.

09-26-2019, 12:20 AM	#26
i.weber Not Yet Wild Join Date: Sep 2019 Posts: 47	Re: Alltrax XTC Controller Help Just noticed tonight that I haven't heard my reverse buzzer since I installed the new controller. Is this common? Other than that, no other issues. Sent from my SM-G975U using Tapatalk
i.weber Not Yet Wild Join Date: Sep 2019 Posts: 47

09-26-2019, 05:36 AM	#27
Sergio Gone Wild Join Date: Sep 2012 Location: Charlotte, NC Posts: 9,329	Re: Alltrax XTC Controller Help The reverse buzzer should work as before, if you wired anything behind the dash make sure the buzzer did not unplugged (put the cart on Tow before removing the dash). How did you fix the rough throttle?

Similar Threads
Thread	Forum
New Alltrax controller	Electric EZGO
Alltrax SPM vs AXE controller	Electric EZGO
ISO: alltrax dcx controller	Golf Carts and Parts
Alltrax controller	Electric Club Car
Alltrax 650 amp Axe controller	Electric Club Car

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum