lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric EZGO
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV.



Post New Thread  Reply
 
Thread Tools Display Modes
Old 06-02-2019, 03:30 PM   #11
Newbuggyboy
Gone Wild
E-Z-GO
 
Join Date: Feb 2019
Location: God's Country America
Posts: 883
Default Re: EZ-GO 2008 RXV openCAN not sending info

It is GEN3. By EDT.LLC trade mark Energy Design Tek LLC
Attached Images
File Type: jpg 20190602_162759.jpg (162.7 KB, 0 views)
File Type: jpg 20190602_162754.jpg (238.4 KB, 0 views)
Newbuggyboy is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 06-02-2019, 03:50 PM   #12
yurtle
Gone Mad
E-Z-GO
 
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
Default Re: EZ-GO 2008 RXV openCAN not sending info

Thanks. I like the all black better. Here's mine.

I went to their website and downloaded their Gen3 manual. It still uses a user installed motor temperature sensor, a user installed speed sensor, that counts pulses. One pulse per revolution, so you enter tire circumference, optional external power only says use a key switched power source from 12 to 48 volts. I made sure I downloaded the Gen 3 manual, but they may have something specific to RXVs. I'd think speed would be easier if it came from the controller. One less sensor to install and that may go bad. Dunno if RXV motors have a temp sensor inside the stator windings, but if they do, that would be superior to an externally mounted temp sensor. Voltage can pretty much come from anywhere, though they recommend key switched. Mine is connector to a 10 position rotary switch that's off, pack, batteries 1 - 8, aux battery.
Attached Images
File Type: jpg IMG_3064 (2).JPG (1.54 MB, 0 views)
File Type: jpg IMG_2244.jpg (250.3 KB, 0 views)
yurtle is offline   Reply With Quote
Old 06-02-2019, 03:57 PM   #13
Newbuggyboy
Gone Wild
E-Z-GO
 
Join Date: Feb 2019
Location: God's Country America
Posts: 883
Default Re: EZ-GO 2008 RXV openCAN not sending info

Yurtle did u see my post that include 2 pictures and wiring instructions for rxvs?

The question is can I tap the blk/white and red?
Newbuggyboy is offline   Reply With Quote
Old 06-02-2019, 03:59 PM   #14
yurtle
Gone Mad
E-Z-GO
 
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
Default Re: EZ-GO 2008 RXV openCAN not sending info

Quote:
Originally Posted by Newbuggyboy View Post
Yurtle did u see my post that include 2 pictures and wiring instructions for rxvs?
I did, but I didn't know the source, and didn't see it in their manual. Not really important, I'm just curious. Does it get speed and temp from the controller?
yurtle is offline   Reply With Quote
Old 06-02-2019, 04:13 PM   #15
BobBoyce
Gone Insane
E-Z-GO
 
Join Date: Oct 2015
Location: TN/NC/GA Tri-state area
Posts: 3,952
Default Re: EZ-GO 2008 RXV openCAN not sending info

The RXV has a temperature sensor embedded in the windings. The speed encoder is dual channel 5V pulses. Phase differential shows motor spin direction, pulse rate indicates RPM.

The CAN bus signal digitally communicates SOC percentage only on the RXV by default, without being queried for it. The 2Five rotates through a number of data sequences, as it provides information to the speedometer display. The device connected identifies itself to the controller, so the controller provides the data that the device is requiring.
BobBoyce is offline   Reply With Quote
Old 06-02-2019, 05:36 PM   #16
Newbuggyboy
Gone Wild
E-Z-GO
 
Join Date: Feb 2019
Location: God's Country America
Posts: 883
Default Re: EZ-GO 2008 RXV openCAN not sending info

Quote:
Originally Posted by BobBoyce View Post
The RXV has a temperature sensor embedded in the windings. The speed encoder is dual channel 5V pulses. Phase differential shows motor spin direction, pulse rate indicates RPM.

The CAN bus signal digitally communicates SOC percentage only on the RXV by default, without being queried for it. The 2Five rotates through a number of data sequences, as it provides information to the speedometer display. The device connected identifies itself to the controller, so the controller provides the data that the device is requiring.

So does that mean yes? And I can use the red and blk/white?
Newbuggyboy is offline   Reply With Quote
Old 06-02-2019, 05:49 PM   #17
yurtle
Gone Mad
E-Z-GO
 
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
Default Re: EZ-GO 2008 RXV openCAN not sending info

Quote:
Originally Posted by Newbuggyboy View Post
So does that mean yes? And I can use the red and blk/white?
Your attachment on Post #3 also says, "Another option is to connect the EXRAY power wires to the KEY SWITCH RED wire and a BLACK wire that is Battery Negative."
yurtle is offline   Reply With Quote
Old 06-02-2019, 05:54 PM   #18
Newbuggyboy
Gone Wild
E-Z-GO
 
Join Date: Feb 2019
Location: God's Country America
Posts: 883
Default Re: EZ-GO 2008 RXV openCAN not sending info

Quote:
Originally Posted by yurtle View Post
Your attachment on Post #3 also says, "Another option is to connect the EXRAY power wires to the KEY SWITCH RED wire and a BLACK wire that is Battery Negative."
Didn't u say this:

Quote:
Originally Posted by yurtle View Post
Don't tap into ANY wire. You'll kill the controller. Here's the only place to get what you need. This needs to be the trigger wire for a 12 volt relay. How will you get 12 volts?
Thanks I read that. Can u answer my question?
Newbuggyboy is offline   Reply With Quote
Old 06-02-2019, 06:13 PM   #19
yurtle
Gone Mad
E-Z-GO
 
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
Default Re: EZ-GO 2008 RXV openCAN not sending info

Quote:
Originally Posted by Newbuggyboy View Post
Didn't u say this:



Thanks I read that. Can u answer my question?
I can for getting pack positive from solenoid and pack negative at battery. What I can't answer, because I don't know, is whether their suggestion about using the CAN wires are safe. I'm not even their suggestion to use the key switch is safe, but there are folks who do know.

There is a difference between a reducer that pulls 10 amps, and a volt meter/clock/temp/odo/speedo, which is in the milliamps range.
yurtle is offline   Reply With Quote
Old 06-02-2019, 06:18 PM   #20
Newbuggyboy
Gone Wild
E-Z-GO
 
Join Date: Feb 2019
Location: God's Country America
Posts: 883
Default Re: EZ-GO 2008 RXV openCAN not sending info

Let's keep it simple. U don't know.
Newbuggyboy is offline   Reply With Quote
Reply

Tags
canalyst2, canbus, canopen, canprotocol, ezgo
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric EZGO


Thread Tools
Display Modes


Similar Threads
Thread Forum
Sending unit Gas Club Car
2008 ezgo 2+2 swap info Big Block Talk!
Oil sending unit wire Gas EZGO
Sending it to PQ Electric Club Car


All times are GMT -5. The time now is 03:50 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2023, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.