05-02-2016, 08:28 AM | #1 |
Gone Wild
Join Date: Apr 2015
Location: Pennsylvania
Posts: 378
|
Tomberlin Accelerator
Anyone know where I could buy a new ITS for a tomberlin E-merge? Its the two wire version...I've noticed with some other parts the sticker on it doesn't seem to directly correspond to the part number so searching it didn't turn anything up.
Sticker: F10604076 |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-06-2017, 06:02 PM | #2 |
Gone Wild
Join Date: Sep 2008
Location: Eastern NC
Posts: 432
|
Re: Tomberlin Accelerator
I am looking one also,did you have any luck finding one,or anyone that sells parts?
|
08-07-2017, 10:24 AM | #3 |
Gone Wild
Join Date: Apr 2015
Location: Pennsylvania
Posts: 378
|
Re: Tomberlin Accelerator
I actually ended up using an EZGO ITS. I have what looks to be an experimental/early version of a 0-5V output ITS. They have an external circuit board to condition the signal and regulate the battery voltage for a standard ITS to work with it. (Two tabs). From what I have seen going forward they have 3 tabs since they put the board inside the base of the ITS itself. (B+, B-, Signal)
|
08-07-2017, 08:23 PM | #4 |
Gone Wild
Join Date: Sep 2008
Location: Eastern NC
Posts: 432
|
Re: Tomberlin Accelerator
My cart,troubleshoot how?
|
08-08-2017, 06:30 AM | #5 |
Gone Wild
Join Date: Apr 2015
Location: Pennsylvania
Posts: 378
|
Re: Tomberlin Accelerator
That blue wire coming off the board should have a 0-5V swing with the pedal. B+ on the red, B- on the black. The ITS should have close to 12 or 15v on one side and something like 1~3v swing on the other. However, knowing a specific fault code helps. 1268 controls blink a status code if you do not have a handset.
|
08-08-2017, 09:10 AM | #6 |
Gone Wild
Join Date: Sep 2008
Location: Eastern NC
Posts: 432
|
Re: Tomberlin Accelerator
Led blink code 1-2
|
08-08-2017, 10:31 AM | #7 |
Gone Wild
Join Date: Apr 2015
Location: Pennsylvania
Posts: 378
|
Re: Tomberlin Accelerator
1,2 is Throttle Fault
The valid range for this control's throttle according to the programming is 0.4V - 4.5V (0%-100%) The fault range is >0 or <5. Pin 15 of the controller should likely be something like 0.1~0.3V at pedal off and probably 4.6~4.9 at full on. I imagine if something on that PCB were shorted you may see 15 or battery there instead. 2,1 is Low battery voltage (Just in case, sometimes folks read the blinks backwards) Make sure your pack voltage reads about 50v on a good charge. (pins 2, and 4 of the controller should also read equal to pack) |
08-08-2017, 12:09 PM | #8 |
Gone Wild
Join Date: Sep 2008
Location: Eastern NC
Posts: 432
|
Re: Tomberlin Accelerator
You mention pins 2 ,4 etc, do u have wiring diagram showing PIN numbers?
|
08-09-2017, 07:40 AM | #9 | |
Gone Wild
Join Date: Apr 2015
Location: Pennsylvania
Posts: 378
|
Re: Tomberlin Accelerator
Quote:
Page12 |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Tomberlin won't go over 5 mph | Tomberlin | |||
tomberlin | Electric EZGO | |||
Tomberlin LSV | Tomberlin | |||
Tomberlin | Tomberlin | |||
Tomberlin | Tomberlin |