|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
09-14-2013, 11:21 AM | #21 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: need help! dcs clicks but wont move
Quote:
The throttle input to the controller tells the controller how far to open the valve to the Armature and something that is called a Field Map, tells the controller how far to open the valve going to the Stator (Field) windings based on amp flow through the Armature and some other factors. I'm not sure how high the Stator voltage gets in a DCS, but in a PDS, which is what replaced the DCS, it only gets up to about 2.7V. If you are getting Zero volts between the S1 and S2 terminals on the motor, disconnect the S1 and S2 cables at the controller and measure between the two cables with an Ohmmeter. If you don't have continuity, the cables or the motor is bad. If you do have continuity, the controller might be bad. |
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-14-2013, 12:24 PM | #22 |
Gone Wild
Join Date: Oct 2010
Location: Lancaster SC
Posts: 827
|
Re: need help! dcs clicks but wont move
yeah ive got continuity between each one. im just gonna give up and buy a controller. hell i need a better one in the long run anyway. i just was hoping to drive it till i buy a better one.
|
09-14-2013, 12:56 PM | #23 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: need help! dcs clicks but wont move
A DCX400 will give you more speed and torque and you'll love it.
|
09-14-2013, 01:39 PM | #24 |
Gone Wild
Join Date: Oct 2010
Location: Lancaster SC
Posts: 827
|
Re: need help! dcs clicks but wont move
yeah thats what i want to get from scotty. i just dont have $500 in my budget.
on a side note i took the cover off of the controller and the prong that my S2 wire attaches to is broken loose from the solder connections and the S1 prong is loose. im gonna try and reattach these and see if that does anything |
09-23-2013, 01:04 PM | #25 |
Gone Wild
Join Date: Oct 2010
Location: Lancaster SC
Posts: 827
|
Re: need help! dcs clicks but wont move
ok so i picked up a used controller and i want to make sure i install it right and not mess it up as well. as long as the key isnt switched on and the switch is in the maintenance position i can make all my connections without a problem correct? do i connect to the batteries before or after connecting to the controller?
|
09-23-2013, 02:29 PM | #26 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: need help! dcs clicks but wont move
Quote:
It will spark a little if the pack has been disconnected from the controller for several minutes or more. (Filter capacitors in the controller) Of course, the last step is placing the Run/Tow switch to RUN. |
|
09-24-2013, 12:19 PM | #27 |
Gone Wild
Join Date: Oct 2010
Location: Lancaster SC
Posts: 827
|
Re: need help! dcs clicks but wont move
it moves! the controller was indeed bad. I swapped it out with another one and it works great! thanks to everyone including JohnnyB for the help and info.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
club car clicks but wont move | Electric Club Car | |||
EZGO just clicks wont move | Electric EZGO | |||
92 club car clicks but wont move | Electric Club Car | |||
95Carryall just clicks,wont move | Electric Club Car | |||
solenoid clicks/ wont move | Electric EZGO |