|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
04-10-2020, 09:13 PM
|
#1 |
|
Gone Wild
Join Date: Feb 2020
Posts: 150
|
There has to be a better way
It looks like it’ll work but man it’s screaming redneck. Give me some recommendations or ways that you did the resistor conversion.
 Sent from my iPhone using Tapatalk |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
04-10-2020, 10:08 PM
|
#2 |
|
Gone Insane
 Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: There has to be a better way
Have you got a photo so we can see more of the cart/how the seat will lay over that?
|
|
|
|
|
04-11-2020, 08:36 AM
|
#3 |
|
Gone Wild
Join Date: Feb 2020
Posts: 150
|
Re: There has to be a better way
 Here you go. I’ve seen some conversions and they have a nice bracket setup. But I guess you can get that without buying the whole kit. Sent from my iPhone using Tapatalk |
|
|
|
|
04-11-2020, 10:00 AM
|
#4 |
|
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: There has to be a better way
What's wrong with that ?
 |
|
|
|
|
04-11-2020, 01:07 PM
|
#5 |
|
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: There has to be a better way
If the license plate is sturdy enough to not move around it should hold the throttle OK.
I think you need more than one bolt holding the controller. |
|
|
|
|
04-11-2020, 02:49 PM
|
#6 |
|
Gone Wild
Join Date: Feb 2020
Posts: 150
|
Re: There has to be a better way
The controller has two bolts. Just hard to see.
I’ve got it all wired up. But it doesn’t move. Solenoid clicks. I double and triple checked the wiring. I found this diagram on here somewhere. I highlight each wire making sure it’s correct. Batteries are full (38.4). The left or right sides of micro switches or solenoids don’t matter correct? Switches just make a connection....and about the same for solenoids, correct? Time to start chasing voltages...I know there is a thread somewhere on here, can someone point me to it? |
|
|
|
|
04-11-2020, 03:35 PM
|
#7 |
|
Gone Wild
Join Date: Feb 2020
Posts: 150
|
Re: There has to be a better way
Maybe another disclosure is needed....it’s a Curtis 1204-410 controller. From a club car...I re-wired the pot box to output 5k-0. Maybe I should be looking at a club car wiring diagram.
|
|
|
|
|
04-11-2020, 04:01 PM
|
#8 |
|
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: There has to be a better way
Have you checked the pot output?
|
|
|
|
|
04-11-2020, 04:10 PM
|
#9 |
|
Gone Wild
Join Date: Feb 2020
Posts: 150
|
Re: There has to be a better way
Not pressed is 4.8k and pressed is 34.
|
|
|
|
|
04-11-2020, 04:13 PM
|
#10 |
|
Gone Insane
Join Date: Oct 2016
Location: Richmond, VA
Posts: 14,215
|
Re: There has to be a better way
34, or .034?
|
|
|
|
|
|
||||||
|
|
Linear Mode
