|
Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
05-20-2010, 10:21 AM | #1 |
EZ Like Sunday Morning
Join Date: Jun 2009
Location: Owatonna, Minnesota
Posts: 465
|
Break in procedure for 2pg EZGO
Going to be doing an upper end overhaul (jug and piston w/rings), any special break in or just run the gas richer?
Thanks guys |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-20-2010, 03:23 PM | #2 |
Not Yet Wild
Join Date: Dec 2009
Posts: 25
|
Re: Break in procedure for 2pg EZGO
I posted the same post a while back and didn't get much of an answer. I rebuilt mine a few months back. Ran it about 50:1. I did a real slow first run for about 15 minutes of getting on the throttle about half way and then letting off. Didn't go full throttle for about an hr and a half of steady riding. After the hr and a half I ran it hard the rest of the night and ever since. Rings sat perfect and I am back up to about 120 lbs of compression.
|
05-20-2010, 03:30 PM | #3 |
EZ Like Sunday Morning
Join Date: Jun 2009
Location: Owatonna, Minnesota
Posts: 465
|
Re: Break in procedure for 2pg EZGO
How did you off-set the rings? Did you use any assembly lube?
|
05-20-2010, 03:34 PM | #4 |
Not Yet Wild
Join Date: Dec 2009
Posts: 25
|
Re: Break in procedure for 2pg EZGO
If you got a new piston it will have tabs in the ring grooves. set the gaps on those tabs. just be sure not to move the jug side to side once you have the piston in the jug. It will break those tabs. I just drenched everything in a ton of 2 stroke. I replaced the head gasket, jug, base gasket, piston, rings, and wrist pin. Just soaked all the internal parts. All came in a kit except for the wrist pin. Not sure why the kit wouldn't come with that. It's worth changing it while you have it all apart.
|
05-20-2010, 03:41 PM | #5 |
EZ Like Sunday Morning
Join Date: Jun 2009
Location: Owatonna, Minnesota
Posts: 465
|
Re: Break in procedure for 2pg EZGO
Perfect, thanks!!
|
05-20-2010, 03:52 PM | #6 |
......................
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: Break in procedure for 2pg EZGO
|
05-20-2010, 04:11 PM | #7 |
EZ Like Sunday Morning
Join Date: Jun 2009
Location: Owatonna, Minnesota
Posts: 465
|
Re: Break in procedure for 2pg EZGO
Thanks Rib33024, I plan on doing it next week and that info will be invaluable.
|
05-20-2010, 04:12 PM | #8 |
......................
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: Break in procedure for 2pg EZGO
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Battery breakin or break in procedure procedures | Electric Club Car | |||
Rebuilt a 295cc engine 4 stroke whats the break in procedure | Gas EZGO | |||
Is there a break in procedure for 295cc | Gas EZGO | |||
87 EZGO, axle & break drum, spline drive | Electric EZGO | |||
EZGO rear end break down | Gas EZGO |