|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
08-23-2011, 12:40 PM | #11 |
Not Yet Wild
Join Date: Apr 2011
Posts: 43
|
Re: where to start?
Lol, well lil bro and I have this thing almost down to the frame, I got a ton of cleaning.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
08-23-2011, 12:49 PM | #12 |
Gone Wild
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,901
|
Re: where to start?
Good!!! Look at my build if you think yours is bad. Lol
|
08-23-2011, 05:09 PM | #13 |
Not Yet Wild
Join Date: Apr 2011
Posts: 43
|
Re: where to start?
I actually reference back to your build a lot. Kinda inspiration on the tare down. I just done at the car wash with it. Lots of grime.
|
08-23-2011, 05:21 PM | #14 |
Gone Wild
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,901
|
Re: where to start?
Pressure washer is the best thing you can do for a cart. Glad to see you are doing it the right way!
|
08-23-2011, 05:34 PM | #15 |
Not Yet Wild
Join Date: Apr 2011
Posts: 43
|
Re: where to start?
Before the wash
|
08-23-2011, 05:38 PM | #16 |
Gone Wild
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,901
|
Re: where to start?
So what are your plans for it while to have it down to the frame? O just in general? You going to rebuild it stock, dropped lifted? What do you have in mind. You ask anybody on here I am full of ideas. Some stupid some not!
|
08-23-2011, 08:08 PM | #17 | |
Gone Wild
Join Date: Jun 2010
Location: Central Florida
Posts: 2,757
|
Re: where to start?
Quote:
Are you going to keep the F&R lever or convert it to a Rocker switch on the dash similar to a PDS cart? |
|
08-23-2011, 08:14 PM | #18 |
Gone Wild
Join Date: Jul 2011
Location: Houston, TX
Posts: 2,901
|
Re: where to start?
Thanks for covering my @$$ once again. Lol i was for some reason thinking series because the topic was up in the air! Lol my bad!!
|
08-25-2011, 03:06 PM | #19 |
Not Yet Wild
Join Date: Apr 2011
Posts: 43
|
Re: where to start?
Well I hope too use a switch instead of a lever, I did decide to run 23"x10.5"x12"s. I saw turf tire today that I liked.
I pulled the motor, kinda suprized in such small hardware holding it on. Then started the corrosion clean-up. Yee-Haa!!! DeWalt wire wheel & primer!!! |
08-29-2011, 07:56 PM | #20 |
Not Yet Wild
Join Date: Apr 2011
Posts: 43
|
Re: where to start?
Alright, I'm confused..."series, dcs, pds"? I now have both dcs & pds. SERIOUSLY, 2 carts for free in 1 week. ABSOLUTELY NONE of the electronics are good, I've been reading through everything I can.
I'm wanting to purchase everything NEW. With that being said, can I set up any system I want being that I'm starting from new? And if so.... What is the best route to go? I'm thinking 23" Tires, 6" LT Strech, Assassign motor, 48v, 700amp controller, 2 gauge wires, ect. Clue me in! |
|
|
Similar Threads | ||||
Thread | Forum | |||
G2 will not start | Gas Yamaha | |||
87 CC will not start... | Gas Club Car | |||
Where do I start? | Electric EZGO | |||
87 EZ GO Gas will not start | Gas EZGO | |||
E-Z GO Has Trouble to Start Randomly and Now It Will Not Start | Electric EZGO |