1995 ezgo workhorse, cannot control slow speeds

FRATT70 · 04-07-2008, 08:12 PM

Hello, I am having trouble controlling my cart. It goes fast at top speed and there is no problem but in slow speeds, it jerks and does not run smooth. I have adjusted the govenor making the spring completely tight and i have loosened it completely and there is no change in speed of the cart or the ability to control the speed. I like the speed of the cart but I need to be able to run it slow and controlled.

StoveBolt · 04-07-2008, 08:22 PM

Quote:

Originally Posted by FRATT70

Hello, I am having trouble controlling my cart. It goes fast at top speed and there is no problem but in slow speeds, it jerks and does not run smooth. I have adjusted the govenor making the spring completely tight and i have loosened it completely and there is no change in speed of the cart or the ability to control the speed. I like the speed of the cart but I need to be able to run it slow and controlled.

I had trouble with one surging at low speed, it was the linkage (small rod) running across the drivers side of the motor above the clutch, I don't know what it does but something with the governor, it's adjustable, jointed in the middle and has to have a "little" slack in it, might want to check yours.

mikesmotortoys · 04-07-2008, 08:56 PM

Ruredy has a good thread on governor adjustments - you should read that for reference. Also check to see if your carb butterfly is closing all the way. There is a stop screw that stops the butterfly on the carb (drivers side), make sure it is adjusted to close all the way.

FRATT70 · 04-09-2008, 09:25 AM

Haven't had time to work on the cart but hopefully in the next couple of days I can check it out.

ruredy · 04-09-2008, 02:43 PM

Also,,,,The shorter belt mod helps bunches with getting slow speed driving under control.

Bob-0 · 04-09-2008, 04:25 PM

Quote:

Originally Posted by ruredy

Also,,,,The shorter belt mod helps bunches with getting slow speed driving under control.

Commas Jon?? Haven't we taught you anything yet.............

ruredy · 04-09-2008, 05:02 PM

Quote:

Originally Posted by Bob-0

Commas Jon?? Haven't we taught you anything yet.............

evidently not

FRATT70 · 04-09-2008, 07:11 PM

Hello, OK I looked at the engine and the rod across the engine did not have a joint in if but I extended and shortened it and there was no noticable difference in the control. I only extended the rod 1/4 inch, was this enough?

[IMG]

[/IMG]

I also looked at the carb butterfly and when I pulled the choke it closed all the way. but this is probably not what you are talking about (I really know absolutely nothing).
I did tighten the governor and loosen it with no results.

[IMG]

[/IMG]

[IMG]

[/IMG]

And about the belt, I can grab it and pull it right off. I am thinking of getting the shorter belt but I want to be sure that it is the problem.I also have other problems with keeping it charged but I wll work on those later.

for the help and I am still looking for the answer.

StoveBolt · 04-09-2008, 07:29 PM

I had to lengthen mine, as I said, mine was jointed in the middle and I adjusted it a little
longer so it drooped a little in the middle and it stopped surging at low speed,
is yours surging (like your on and off the peddle even though your holding the peddle steady) ?

StoveBolt · 04-09-2008, 07:40 PM

Might want to try taking it off on one end and adjust
it so it just slips back on without moving the levers.

04-07-2008, 08:12 PM	#1
FRATT70 Gone Wild Join Date: Apr 2008 Location: Punta Gorda, FL Posts: 206	1995 ezgo workhorse, cannot control slow speeds Hello, I am having trouble controlling my cart. It goes fast at top speed and there is no problem but in slow speeds, it jerks and does not run smooth. I have adjusted the govenor making the spring completely tight and i have loosened it completely and there is no change in speed of the cart or the ability to control the speed. I like the speed of the cart but I need to be able to run it slow and controlled.

04-07-2008, 08:56 PM	#3
mikesmotortoys Gone Wild Join Date: Mar 2008 Location: Rockwall, Texas (Dallas / Ft. Worth) Posts: 7,077	Re: 1995 ezgo workhorse, cannot control slow speeds Ruredy has a good thread on governor adjustments - you should read that for reference. Also check to see if your carb butterfly is closing all the way. There is a stop screw that stops the butterfly on the carb (drivers side), make sure it is adjusted to close all the way.
	www.MIKESMOTORTOYS.com www.EZGOPARTSONLINE.com Factory EZGO - Bad Boy Buggy - Dixie Chopper Mowers

04-09-2008, 09:25 AM	#4
FRATT70 Gone Wild Join Date: Apr 2008 Location: Punta Gorda, FL Posts: 206	Re: 1995 ezgo workhorse, cannot control slow speeds Haven't had time to work on the cart but hopefully in the next couple of days I can check it out.

04-09-2008, 02:43 PM	#5
ruredy Born Wild Join Date: Mar 2007 Location: Clover SC. Posts: 5,552	Re: 1995 ezgo workhorse, cannot control slow speeds Also,,,,The shorter belt mod helps bunches with getting slow speed driving under control.

04-09-2008, 07:11 PM	#8
FRATT70 Gone Wild Join Date: Apr 2008 Location: Punta Gorda, FL Posts: 206	Re: 1995 ezgo workhorse, cannot control slow speeds Hello, OK I looked at the engine and the rod across the engine did not have a joint in if but I extended and shortened it and there was no noticable difference in the control. I only extended the rod 1/4 inch, was this enough? [IMG][/IMG] I also looked at the carb butterfly and when I pulled the choke it closed all the way. but this is probably not what you are talking about (I really know absolutely nothing). I did tighten the governor and loosen it with no results. [IMG][/IMG] [IMG][/IMG] And about the belt, I can grab it and pull it right off. I am thinking of getting the shorter belt but I want to be sure that it is the problem.I also have other problems with keeping it charged but I wll work on those later. for the help and I am still looking for the answer.

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum

04-09-2008, 07:29 PM	#9
StoveBolt Gone Wild Join Date: Feb 2008 Location: Brooklyn, Michigan "Home of M.I.S." Posts: 3,739	Re: 1995 ezgo workhorse, cannot control slow speeds I had to lengthen mine, as I said, mine was jointed in the middle and I adjusted it a little longer so it drooped a little in the middle and it stopped surging at low speed, is yours surging (like your on and off the peddle even though your holding the peddle steady) ?

04-09-2008, 07:40 PM	#10
StoveBolt Gone Wild Join Date: Feb 2008 Location: Brooklyn, Michigan "Home of M.I.S." Posts: 3,739	Re: 1995 ezgo workhorse, cannot control slow speeds Might want to try taking it off on one end and adjust it so it just slips back on without moving the levers.

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode

Similar Threads
Thread	Forum
EZGO Slow up hills	Electric EZGO
88 EZGO Workhorse Oil Injected Help	Gas EZGO
1999 EZGO Jacobson Workhorse	Gas EZGO
1995 electric EZGO to 45hp Arctic Cart conversion	Members Rides