Sepex motor

jbaxley65 · 10-07-2021, 05:47 PM

Any body have any luck finding a sepex high speed motor for a 97 ezgo dcs ?

jbaxley65 · 10-08-2021, 10:04 AM

Quote:

Originally Posted by jbaxley65

Any body have any luck finding a sepex high speed motor for a 97 ezgo dcs ?

Maybe i should of said shunt motor

JohnnieB · 10-08-2021, 10:46 AM

The answer is the same whatever you call it.

The Dana/Spicer rear axle assemblies used by EZGO from about 1988 to present have a 19 spline input shaft, so just about any motor that'll mate up with the mounting flange and fit between the transaxle (aka differential) and the rear shock will work. Of course the motor type will have to be compatible with the drive system (Controller, control wiring, etc.) installed in the cart.

In a nutshell, any SepEx motor that will run in a PDS or TXT48 will also run in a DCS, so a wide variety of motors are available. Of course, the controller has to be compatible with the motor, but the stock DCS controller is a failed design and ought to be replaced with an aftermarket controller, such as an Alltrax XCT48400-DCS.

jbaxley65 · 10-09-2021, 06:37 AM

Thank you! That makes things a little clearer, I have replaced the controller with a Alltrax XCT48400-DCS and hd solenoid. So now to search for the motor again. thanks

JohnnieB · 10-09-2021, 12:24 PM

Quote:

Originally Posted by jbaxley65

Thank you! That makes things a little clearer, I have replaced the controller with a Alltrax XCT48400-DCS and hd solenoid. So now to search for the motor again. thanks

Be sure to install the correct field map for whatever motor you get into the XCT.

10-07-2021, 05:47 PM	#1
jbaxley65 Not Yet Wild Join Date: Sep 2021 Posts: 10	Sepex motor Any body have any luck finding a sepex high speed motor for a 97 ezgo dcs ?
jbaxley65 Not Yet Wild Join Date: Sep 2021 Posts: 10

10-08-2021, 10:46 AM	#3
JohnnieB Techno-Nerd Join Date: Jun 2011 Location: West Virginia Posts: 19,654	Re: Sepex motor The answer is the same whatever you call it. The Dana/Spicer rear axle assemblies used by EZGO from about 1988 to present have a 19 spline input shaft, so just about any motor that'll mate up with the mounting flange and fit between the transaxle (aka differential) and the rear shock will work. Of course the motor type will have to be compatible with the drive system (Controller, control wiring, etc.) installed in the cart. In a nutshell, any SepEx motor that will run in a PDS or TXT48 will also run in a DCS, so a wide variety of motors are available. Of course, the controller has to be compatible with the motor, but the stock DCS controller is a failed design and ought to be replaced with an aftermarket controller, such as an Alltrax XCT48400-DCS.

10-09-2021, 06:37 AM	#4
jbaxley65 Not Yet Wild Join Date: Sep 2021 Posts: 10	Re: Sepex motor Thank you! That makes things a little clearer, I have replaced the controller with a Alltrax XCT48400-DCS and hd solenoid. So now to search for the motor again. thanks
jbaxley65 Not Yet Wild Join Date: Sep 2021 Posts: 10

Similar Threads
Thread	Forum
Sepex motor and rearend	Golf Carts and Parts
Sepex motor specs?	Lifted Golf Carts
96' series or sepex motor	Electric Club Car
WTB Sepex Motor for 99 48v regen 2	Golf Carts and Parts
Sepex Motor Question	Electric EZGO

Today
BGW	Sponsored Links __________________ This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum