|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
09-26-2014, 11:55 AM | #11 |
Not Yet Wild
Join Date: Jun 2013
Posts: 42
|
Re: 36 volt 1995 ezgo ds controller help
Throttle position sensor. Replaced the controller. Car ran. Flipped run/tow switch. Blew controller.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
09-26-2014, 12:17 PM | #12 |
What the ....?
Join Date: Jan 2007
Location: N.E. Wisconsin
Posts: 14,932
|
Re: 36 volt 1995 ezgo ds controller help
|
09-26-2014, 02:12 PM | #13 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: 36 volt 1995 ezgo ds controller help
|
09-26-2014, 05:24 PM | #14 |
Not Yet Wild
Join Date: Jun 2013
Posts: 42
|
Re: 36 volt 1995 ezgo ds controller help
Ok controller was changed. Waited about an hour turned the key on not the run/tow then hit accelerator and toasted the controller.
|
09-26-2014, 05:37 PM | #15 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: 36 volt 1995 ezgo ds controller help
Ouch. I could be the F1 and F2 wires are shorted out to the frame where they go behind the batteries. Or the motor could have a short? Check the F wires for abrasion as shown below.
Remove the 4 wires from the motor - take care NOT to spin the studs. With an ohm Ω meter check for continuity between studs. You should have continuity between F1 and F2 and between A1 and A2 but not between any F and any A terminals. Note early DCS your studs may be marked S1&2 and A1&2. |
10-07-2014, 12:06 PM | #16 |
Not Yet Wild
Join Date: Jun 2013
Posts: 42
|
Re: 36 volt 1995 ezgo ds controller help
We have replaced the wires off the motor. New motor. New controller.
I uploaded 3 pictures. The red wire comes off the solenoid back up towards the forward reverse switch but was not connected. Is there supposed to be a jumper wire on top of the forward reverse switch? We have continunity between a1-a2 and between s1-s2 but not between any a and s |
10-08-2014, 07:09 AM | #17 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 36 volt 1995 ezgo ds controller help
Quote:
2. Yes. See attached schematic and attached picture of early style DCS F/R switch |
|
10-08-2014, 11:39 AM | #18 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: 36 volt 1995 ezgo controller help
Note the little red wire with the large ring terminals goes on the battery side of the solenoid not the controller side.... this gives a constant 36v(+) connection for the control. I don't know how you are running without it. I suspect something else is not wired per diagram. Given the history here I would print the diagram above and trace it out wire by wire against your cart considering the high cost of controllers these days.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
1995 Medalist 36 volt controller question | Electric EZGO | |||
Need wiring diagram for a 1995 ezgo 36 volt medalist | Electric EZGO | |||
WTB..F/R switch 36 volt 1995 ezgo series cart | Golf Carts and Parts | |||
Wtb controller 1995 ezgo | Golf Carts and Parts | |||
1995 Ezgo 36 volt wont move | Electric EZGO |