|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
10-07-2022, 11:33 AM
|
#141 |
|
Not Yet Wild
Join Date: May 2021
Location: Trenton, SC
Posts: 22
|
Re: I need bob boyce to program my controller.
Will it make any difference if he reprogrammed it to the 100% vice 75%?
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
10-07-2022, 11:36 AM
|
#142 |
|
Gone Wild
 Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,173
|
Re: I need bob boyce to program my controller.
If he changed it to 100% it would need the 48 volt but that usually isn’t something he changes unless requested. Simple to check. Put a volt meter on the two smaller terminals of the solenoid and turn on the cart. If it reads high 30s it is set to 75%. Note that after it has been on for a little bit it will drop to the holding voltage which is lower.
|
|
|
|
|
10-07-2022, 11:40 AM
|
#143 |
|
Not Yet Wild
Join Date: May 2021
Location: Trenton, SC
Posts: 22
|
Re: I need bob boyce to program my controller.
Thank you very much
|
|
|
|
|
10-11-2022, 10:08 AM
|
#144 |
|
Not Yet Wild
Join Date: Sep 2022
Location: Cumming, GA
Posts: 7
|
Re: I need bob boyce to program my controller.
Sounds like Bob is no longer doing the controller programing. usgicollector, are you doing them? I'd really appreciate some help on it. I just picked up a 2018 RXV, looks to be a fleet model and speed is limited to around 14 mph. Definitely would like to get this cart sped up a bit. TIA!
|
|
|
|
|
10-11-2022, 10:41 AM
|
#145 |
|
Gone Wild
Join Date: Mar 2014
Location: NE Indiana & SW Florida
Posts: 3,237
|
Re: I need bob boyce to program my controller.
Get another post in and send me a pm I'll get it done for you.
|
|
|
|
|
10-11-2022, 10:49 AM
|
#146 |
|
Not Yet Wild
Join Date: Sep 2022
Location: Cumming, GA
Posts: 7
|
Re: I need bob boyce to program my controller.
Great, I really appreciate it. Will PM you once the system allows me to.
|
|
|
|
|
10-11-2022, 10:55 AM
|
#147 |
|
Gone Wild
Join Date: Mar 2014
Location: NE Indiana & SW Florida
Posts: 3,237
|
Re: I need bob boyce to program my controller.
 |
|
|
|
|
10-31-2022, 11:32 PM
|
#148 |
|
Not Yet Wild
Join Date: Oct 2022
Posts: 5
|
Re: I need bob boyce to program my controller.
Can he program a Dart EV w/ the right setup being a 72V?
|
|
|
|
|
05-26-2023, 10:32 AM
|
#149 |
|
Not Yet Wild
Join Date: May 2021
Location: Trenton, SC
Posts: 22
|
Re: I need bob boyce to program my controller.
I checked the solenoid. It is getting 31v from the controller. Not 36 or 48. Batteries are fully charged. Could it have been a typo during the programming? or is 31v normal?
|
|
|
|
|
05-26-2023, 11:10 AM
|
#150 |
|
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,173
|
Re: I need bob boyce to program my controller.
Could be a typo but like I said the controller will drop voltage to the solenoid so it will run cooler. You need the 36 volt version.
|
|
|
|
|
| Tags |
| usgicollector |
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Program Ez-go rxv bob boyce | Electric EZGO | |||
| Bob Boyce programmed my 2016 rxv fleet curtis controller | Electric EZGO | |||
| RXV controller not responding to upgrade handheld device to program controller | Electric EZGO | |||
| 1999 DS program controller | Electric Club Car | |||
Linear Mode
