|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
06-29-2016, 08:24 AM | #1 |
Not Yet Wild
Join Date: Jul 2015
Posts: 11
|
Convert DCS to PDS?
My friend's DCS sepex cart keeps breaking the reverse microswitch. Can it be converted to the PDS style forward / reverse switch without too much trouble?
Thanks, John |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-29-2016, 08:45 AM | #2 |
Gone Wild
Join Date: Sep 2015
Posts: 572
|
Re: Convert DCS to PDS?
I guess it depends on your definition of "too much trouble". By my definition, no.
|
06-29-2016, 08:52 AM | #3 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,410
|
Re: Convert DCS to PDS?
I think what you are asking about is can he change from the DCS shift device with the $30 micro switches to the PDS rocker switch. This is a fairly common request here. Below is the diagram for the conversion. Note the diode and it's direction between the green and yellow wires. A standard 1-3 amp golf cart diode like IN4004 will suffice.
If you are asking about changing the drive system from DCS to PDS that can easily be done also - just needs a few more parts |
06-29-2016, 09:02 AM | #4 |
Not Yet Wild
Join Date: Jul 2015
Posts: 11
|
Re: Convert DCS to PDS?
Scottyb, that is exactly what I was looking for. Thank you!
|
06-29-2016, 10:14 AM | #5 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Convert DCS to PDS?
FWIW: EZGO mislabeled the F/R switch functions on their DCS schematics.
The top set of contacts ought to be labeled "RUN" instead of "FORWARD" since they have to be closed in both Forward and Reverse. (The top contacts forward pack voltage from the Run/Tow switch to the Keyswitch, which in turn forwards the voltage to the solenoid.) The bottom set of contacts forward pack voltage to Pin-4 on the controller, telling it to go into the reverse mode of operation. (A DCS controller defaults to the Forward mode.) Either a DPDT/center OFF switch can be used or a SPDT/center OFF (Like the PDS rocker switch) with a diode installed can be used. |
06-29-2016, 12:32 PM | #6 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,146
|
Re: Convert DCS to PDS?
I would think a DPDT center off with a nice housing similar to the club car would fit nicely over the original hole left by taking out the current FnR switch..
|
06-29-2016, 01:20 PM | #7 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Convert DCS to PDS?
Quote:
The CC F/R switch by your knee is a lot easier to reach than the EZGO PDS F/R switch on the dash. Also, you don't have to extend the wires to reach the dash. |
|
06-29-2016, 03:40 PM | #8 |
Not Yet Wild
Join Date: Jul 2015
Posts: 11
|
Re: Convert DCS to PDS?
I was going to recommend that he get one of ScottyB's key/forward-reverse/voltage meter panels to replace his, but the CC leg mounted switch may be a better solution. Anyone know if it will cover the hole left by the old selector?
|
06-30-2016, 12:05 PM | #9 |
Gone Wild
Join Date: Dec 2009
Location: Aiken, SC
Posts: 13,146
|
Re: Convert DCS to PDS?
Yes it will just fine.. I have converted a couple of my PDS carts to this setup and the bodies are the same.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Convert | Electric Club Car | |||
convert a 36 or buy a 48? | Electric golf carts | |||
convert from dcs to pds | Electric EZGO | |||
Should I Convert to 48V | Electric EZGO |