|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
02-04-2015, 04:24 PM | #1 |
Not Yet Wild
Join Date: Feb 2015
Location: augusta,ga
Posts: 10
|
1999 ezgo series wont go
my 1999 standard series ezgo wont move, it tries to very weak. i just put new batteries in made sure all the connections were clean and tight as well as all other connections and terminals any ideas
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
02-04-2015, 04:35 PM | #2 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
|
Re: 1999 ezgo series wont go
DO you have a test meter? Put the test leads on the 2 battery posts that connect to the cart. What's the voltage read?
|
02-05-2015, 07:48 AM | #3 |
Not Yet Wild
Join Date: Feb 2015
Location: augusta,ga
Posts: 10
|
Re: 1999 ezgo series wont go
yea, i have voltage 38 on the batteries, voltage on all f&r lugs and speed controller. i swapped moters and im thinking it may be for dcs and pds carts not series. any help on this is greatly appreciated.
|
02-05-2015, 07:52 AM | #4 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 1999 ezgo series wont go
What is the Make & Model of motor?
|
02-05-2015, 08:00 AM | #5 |
Not Yet Wild
Join Date: Feb 2015
Location: augusta,ga
Posts: 10
|
Re: 1999 ezgo series wont go
cant tell
|
02-05-2015, 09:11 AM | #6 | |
Master of All Things
Join Date: May 2013
Location: West Columbia, Texas
Posts: 17,892
|
Re: 1999 ezgo series wont go
Quote:
if the 2 closest to the tranny are smaller.....you got the wrong type of motor plugged into your cart. if all 4 are the same size....you will need to get the info off of the motor name plate..... OR are the 4 posts labeled at all? of so.....if its a series motor they will be labeled A1, A2, S1, and S2. if its a sepex motor they will be labeled A1, A2, F1, and F2 |
|
02-05-2015, 09:54 AM | #7 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
|
Re: 1999 ezgo series wont go
Use this chart to determine the drive system type.
|
02-05-2015, 10:23 AM | #8 |
Not Yet Wild
Join Date: Feb 2015
Location: augusta,ga
Posts: 10
|
Re: 1999 ezgo series wont go
might have other issues then the moter has s1 s2 a1 a2.
|
02-05-2015, 11:42 AM | #9 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 1999 ezgo series wont go
The studs of some of the DCS motors were labeled S1&S2 and A1&A2 and all four studs were the same size.
You'll have to find a label on the motor or pull it and look at the field windings ( you can see the difference in the chart Scotty posted). You also might be able to tell using an Ohmmeter. The Armature and Stator windings of a series motor will be about the same, while the Field windings of a Sepex motor will have considerable more resistance then the Armature. (IE: My sepex motor is about 1.0Ω for the armature and about 3.0Ω for the field.) |
02-05-2015, 02:27 PM | #10 |
Not Yet Wild
Join Date: Feb 2015
Location: augusta,ga
Posts: 10
|
Re: 1999 ezgo series wont go
thanks Johnnie, i will check when i get off work today.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
ezgo TXT 1999 wont run | Electric EZGO | |||
need help with 1999 ezgo series direction control | Electric EZGO | |||
1999 ezgo txt wont run in forward | Electric Club Car | |||
1999 ezgo 36 volt series wont run | Electric EZGO | |||
1999 EZGO Series Cart HELP!! | Electric EZGO |