![]() |
|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
![]() ![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Not Yet Wild
![]() Join Date: Sep 2008
Location: Benson AZ.
Posts: 14
|
![]() My charger stopped working I checked it out and found there was no low voltage to the relay, orange and brown wires have no power when I jump out the relay the charger works. could it be one of the boards? any ideas. Thanks Arizona Bob
|
![]() |
![]() |
![]() |
|
![]() __________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
![]() |
#2 |
The Last Moja Morani
![]() ![]() Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
![]() check the volyahe in the cart 1st to make sure you have enough to turn the charger on.........you need 26 to 28 volts otherwise charger won,t come on............................................
![]() |
![]() |
![]() |
![]() |
#3 |
Not Yet Wild
![]() Join Date: Sep 2008
Location: Benson AZ.
Posts: 14
|
![]() The cart has 37 volts and runs fine. Arizona Bob
|
![]() |
![]() |
![]() |
#4 |
The Last Moja Morani
![]() ![]() Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
![]() yes it could be circuit breaker, relay, board, doiodes......hard to tell without the manual to start testing the componants otherwise were just throwing parts into it till we get lucky.......................do you have a manual? if so everything for charger will be there.............testing in order and diagnosing..................
![]() |
![]() |
![]() |
![]() |
#5 |
48/400/Alltrax HS motor
![]() Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,187
|
![]() Most of the time if you jump the relay and it comes on it's the relay.Black lines are the two wires you need to jump.
![]() |
![]() |
![]() |
![]() |
#6 |
Not Yet Wild
![]() Join Date: Sep 2008
Location: Benson AZ.
Posts: 14
|
![]() Tom I jumped out relay it works installed a new relay and it works only if you jump out the new relay. I have no power to the orange and brown wires that power the relay coil. I'm going to check farther now that you provided a wiring diagram. Thanks a lot. Bob
|
![]() |
![]() |
![]() |
#7 |
The Last Moja Morani
![]() ![]() Join Date: Jan 2007
Location: jumping from cart to cart
Posts: 8,975
|
![]() thank andy for the diagram, hes the man when you need one of those..................
![]() |
![]() |
![]() |
![]() |
#8 |
Gone Wild
![]() Join Date: Aug 2008
Location: Cumming, GA
Posts: 313
|
![]() If it is not the board it is will be the diodes mounted to the heat sink board and or the the fuse. TYpically if the diodes go bad it will take out the fuse.
|
![]() |
![]() |
![]() |
#9 |
Getting Wild
Join Date: Jul 2009
Posts: 80
|
![]() I know my problem is with the black relay mounted on the board. I have to take the two wires off the relay and tape them together and my charger will work even though I know it is not safe. So my question is this. Can I just replace the relay on the board? If so where can I buy just the relay?
|
![]() |
![]() |
![]() |
|
Thread Tools | |
Display Modes | |
|
![]() |
||||
Thread | Forum | |||
36 volt powerwise charger for sale | Golf Carts and Parts | |||
48 Volt Charger | Golf Carts and Parts | |||
powerwise charger not working | Electric EZGO | |||
Need 36 and 48 volt charger | Golf Carts and Parts | |||
36 volt charger | Electric EZGO |