|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
06-25-2019, 03:45 PM | #1 |
Gone Wild
Join Date: Apr 2019
Posts: 198
|
Alltrax/SW202/HD Solenoid: clicking no movement
I installed my kit per Scotty’s instructions. The Alltrax instructions have the wiring a little different. Both my reversing contactor and solenoid are clicking but the cart does not move. What do I check first?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
06-25-2019, 03:49 PM | #2 |
Gone Wild
Join Date: Apr 2019
Posts: 198
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
I’m getting five green, then three green and one red and if I hold the throttle it will stay green.
|
06-25-2019, 03:55 PM | #3 |
Gone Wild
Join Date: Apr 2019
Posts: 198
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
So I’m getting movement. I have to press the pedal all the way down (nothing happens) then when I begin to release it it slowly starts to move and goes faster as I release until it’s disengaged. I’m stumped. No wire to hook it up to my laptop until tomorrow.
|
06-25-2019, 05:09 PM | #4 |
Gone Wild
Join Date: Apr 2019
Posts: 198
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
Ohm meter reads 00.2 all the way up and 1.1 when depressed fully. Will swapping the green and white wires to the controller make any difference?
|
06-25-2019, 05:12 PM | #5 |
Gone Wild
Join Date: Apr 2019
Posts: 198
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
Switching those two does nothing.
|
06-25-2019, 05:20 PM | #6 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
When the contactor first clicks what is the LED status code? This first code is the throttle setting. The signal sounds like it is set reversed from what your cart is?
The G8 should be 0-1k aka 0-1000 ohms The Alltrax signal for 0-1k is 5 green blinks Simply depress the gas until the solenoid clicks and hold it there to read. See the codes in the back of your handbook |
06-25-2019, 05:24 PM | #7 |
Gone Wild
Join Date: Apr 2019
Posts: 198
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
It gives me five green blinks
|
06-25-2019, 05:26 PM | #8 |
Gone Wild
Join Date: Apr 2019
Posts: 198
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
After that it gives three green then one red for an uncalibrated throttle over and over. If I press the pedal all the way down it goes constant green. When I begin to let off the cart begins to move.
|
06-25-2019, 05:32 PM | #9 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,419
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
Do you have the software downloaded? Can you connect the controller to a laptop ?
|
06-25-2019, 05:32 PM | #10 |
Gone Wild
Join Date: Apr 2019
Posts: 198
|
Re: Alltrax/SW202/HD Solenoid: clicking no movement
If the rocker switch is in the N position I get the five blinks then a constant green right after.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
SW202 reversing contactor and Alltrax AXE controller | Electric EZGO | |||
36v TXT Solenoid clicking but no movement | Electric EZGO | |||
84 DS Resistor Cart no clicking and no movement | Electric Club Car | |||
Reversing Contactor SW202 click, no movement | Electric EZGO | |||
Clicking noise.....No movement | Electric EZGO |