|
|
|||||||
| Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
10-25-2018, 10:44 AM
|
#1 |
|
Getting Wild
Join Date: Jul 2011
Location: DECATURVILLE, TN.
Posts: 98
|
Pds its testing
Back to this 2001 36 volt pds car.
How do i check the its on a curis 1206 mx controller? Thanks, roy |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
10-25-2018, 11:39 AM
|
#2 |
|
Techno-Nerd
 Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Pds its testing
Here you go.
|
|
|
|
|
10-25-2018, 12:49 PM
|
#3 |
|
Getting Wild
Join Date: Jul 2011
Location: DECATURVILLE, TN.
Posts: 98
|
Re: Pds its testing
Johnnie b,
thanks for the diagram! We need to go to step "46" which is not on what you sent. Could you please send the next step or so that includes "46" thanks, roy |
|
|
|
|
10-25-2018, 12:54 PM
|
#4 |
|
Getting Wild
Join Date: Jul 2011
Location: DECATURVILLE, TN.
Posts: 98
|
Re: Pds its testing
Johnnie b,
not sure you got the message. Recieved your diagram although we need to go to step "46" if you could please send the next step or so. Thanks, roy |
|
|
|
|
10-25-2018, 01:02 PM
|
#5 |
|
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: Pds its testing
Looking at the diagram, one path leads you to "Replace ITS" while the other leads you to 46. I'd assume if you are headed to 46, your ITS is good.
|
|
|
|
|
10-25-2018, 01:52 PM
|
#6 |
|
Getting Wild
Join Date: Jul 2011
Location: DECATURVILLE, TN.
Posts: 98
|
Re: Pds its testing
Adjusted the "its" to specs. Still shuddering with 1/2 to full pedal depression.
Getting lost here or just going mad. Anybody got any suggestions? Thanks, roy |
|
|
|
|
10-26-2018, 10:53 AM
|
#7 |
|
Getting Wild
Join Date: Jul 2011
Location: DECATURVILLE, TN.
Posts: 98
|
2001 ez go pds
Really lost on this car.
I.t.s. Is fine, new speed sensor, curtis 1206 checked okay by fsip, pulled motor and looks and runs with no bearing noise. It will run fine at low speed. When you get from 1/2 to full acceleration it again slows down and the motor studders. What do you think it could be? Thanks, roy |
|
|
|
|
10-26-2018, 11:00 AM
|
#8 | |
|
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: 2001 ez go pds
Quote:
Battery or batteries failing under load. Bad controller. Worn insulation of F1/F2 wires. |
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Best testing practices for testing charging on a G2 | Gas Yamaha | |||
| 99 EZ GO txt ITS testing | Electric EZGO | |||
| Testing 1,2,3 | Test Post | |||
| Testing 1,2,3 | Test Post | |||
| Testing 1, 2, 3... | Test Post | |||
Linear Mode
