|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
03-26-2019, 03:15 PM | #1 |
Not Yet Wild
Join Date: Nov 2018
Posts: 26
|
Alltrax axe 4845 controller
2001 txt 36 volt. When wire 4 is connected cart runs slow. When disconnected cart runs good. Is this normal?
Sent from my SM-T810 using Tapatalk |
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-26-2019, 03:19 PM | #2 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: Alltrax axe 4845 controller
Yes. It's 1/2 speed for reverse and the backup beeper. Normally they're connected to MS4 on the attached wiring diagram.
If you meant it always runs slow, forward and reverse, then MS4 could be bad. It's on the back of the FNR. |
03-26-2019, 03:28 PM | #3 |
Not Yet Wild
Join Date: Nov 2018
Posts: 26
|
Re: Alltrax axe 4845 controller
Thanks. I'm not good with wiring diagrams. Should I keep it disconnected or how do I connect it the right way.
Sent from my SM-T810 using Tapatalk |
03-26-2019, 03:49 PM | #4 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: Alltrax axe 4845 controller
Do you know of anyone who can read a wiring diagram? It's really pretty simple. Microswitch MS4 and MS2 both share a jumper wire, usually red, which should be pack positive referencing pack negative. From there the backup signal or pack positive goes through MS4, which is supposed to be off unless the FNR is in reverse. Then the backup beeper should sound and pack positive goes to controller pin 4 for 1/2 speed. If MS4 is always closed - on - you can just leave it unplugged from controller pin 4 for now. There's nothing wrong with no 1/2 speed reverse, though no backup beeper is not the safest way to go. 1/2 speed reverse is to give you more precise control of the throttle.
|
03-26-2019, 03:58 PM | #5 |
Not Yet Wild
Join Date: Nov 2018
Posts: 26
|
Re: Alltrax axe 4845 controller
Thanks very much. Could it be that the small wires going to the f&r switch got put on the wrong spades. All three were off at one time and I thought that I replaced them on the right spades. They are not color coded. Some idiot painted everything black.
Sent from my SM-T810 using Tapatalk |
03-26-2019, 04:01 PM | #6 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: Alltrax axe 4845 controller
Post a few pics and I'll try and tell you what to connect. Take the cover off of the FNR so I can see the two microswitches.
|
03-26-2019, 04:03 PM | #7 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: Alltrax axe 4845 controller
Use the paperclip to attach pics.
|
03-26-2019, 04:12 PM | #8 |
Not Yet Wild
Join Date: Nov 2018
Posts: 26
|
Re: Alltrax axe 4845 controller
Your the best!
Sent from my SM-T810 using Tapatalk |
03-26-2019, 04:28 PM | #9 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: Alltrax axe 4845 controller
My best guess. I labeled two wires. One should go to the key switch and the other goes to the controller and beeper. Can you tell which is which? Also, there is a spade connector that goes nowhere. Do you know what that is?
The two green wires with spade connectors and plugged in together go from MS2 to the throttle microswitch and is green on the wiring diagram I sent you. |
03-26-2019, 04:32 PM | #10 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: Alltrax axe 4845 controller
Try and get a closeup on each of the two microswitches. I can't follow the wires, and the only two colors I can make out are green and black spray paint. Use highest resolution and use the paperclip to attach.
Click on the thumbnail I attached up top. That's using the paperclip. |
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
alltrax controller | Electric Club Car | |||
Alltrax controller | Electric Club Car | |||
4845 ALTRAX 400 AXE Prog. Controller | Golf Carts and Parts | |||
Will AXE 4845 burn my stock motor? | Electric EZGO | |||
36v cc installed a alltrax 4845 - results | Electric Club Car |