|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
05-27-2018, 07:03 PM | #1 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Yamaha G2-G9 not starting after.....
Hey guys I posted earlier this morning about my muffler studs broke and how to remove them ect...well I got it fixed and looks great only thing is that I did not have a gasket to install just yet, so my question would be would that gasket stop the motor from going ??? Because know all it’s doing is acting like I it’s getting to much fuel/poping here and there curious if it’s getting air from not having that gasket and throwing off the air flow to make it run
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-27-2018, 07:47 PM | #2 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: Yamaha G2-G9 not starting after.....
Nope, should still run and be very loud.
|
05-27-2018, 08:36 PM | #3 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Yamaha G2-G9 not starting after.....
I was looking at it closer and there is one red wire on the that black box had corroded off would that be a problem ? I can’t figure it out this cart always started perfect
|
05-27-2018, 09:54 PM | #4 |
A Gal with a Cart!
Join Date: Aug 2015
Location: Northeast in the Republic of Texas
Posts: 462
|
Re: Yamaha G2-G9 not starting after.....
picture?
Black box? |
05-27-2018, 10:21 PM | #5 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Yamaha G2-G9 not starting after.....
Sorry it’s the igniter and I’ll post pics tomorrow have to figure out how to fix it ?
|
05-27-2018, 11:33 PM | #6 |
Nincompoop village idiot
Join Date: Apr 2018
Location: Michigan
Posts: 9,690
|
Re: Yamaha G2-G9 not starting after.....
You can remove the terminal out of the connector, solder the wire back to the terminal and then put it back into the connector. Probably your best bet
|
05-28-2018, 08:50 AM | #7 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Yamaha G2-G9 not starting after.....
Yea to bad they don’t make a connector to have them all replaced
|
05-28-2018, 11:39 AM | #8 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Yamaha G2-G9 not starting after.....
|
05-28-2018, 11:41 AM | #9 |
Gone Wild
Join Date: May 2010
Location: OHIO
Posts: 1,517
|
Re: Yamaha G2-G9 not starting after.....
|
05-28-2018, 08:35 PM | #10 |
Nincompoop village idiot
Join Date: Apr 2018
Location: Michigan
Posts: 9,690
|
Re: Yamaha G2-G9 not starting after.....
Dont think I'd even bother with that. After seeing how well the Chrysler setup works I think I'd just go that route and sell the ignitor on Ebay or save it for a rainy day
|
|
|
Similar Threads | ||||
Thread | Forum | |||
starting issues g1 yamaha | Gas Yamaha | |||
Hard starting Yamaha G1 | Gas Yamaha | |||
Yamaha G1 Starting | Gas Yamaha | |||
Yamaha G19 hesitation when starting | Electric Yamaha | |||
Gas Yamaha has trouble starting | Gas Yamaha |