ezgo diagrams

[caddymankc]

i found some ezgo engine diagrams not shure what engine though
(edit** this is for both 295 and 350 Robin engines)







i got electric ezgo diagram too i dont know what years there for

(edit ** I am adding part numbers and decriptions to this, I believe most of them are correct but you need to double check when ordering parts)
REF PT# DESCRIPTION

1 25660G3 SERVICE ENGINE 295CC 1
2 72500G05 SERVICE ENGINE 350CC 1
4 72501G01 *CRANKCASE ASY W/BEARNGS-350CC 1
5 26590G01 *CRANKCASE ASY.-COMPLETE-4CYC 1
6 26743G01 *SEAL-OIL-BALANCER SHAFT-4CYC 1
7 26741G01 *SEAL-OIL-CRANKSHAFT-4CYC 1
8 17473G1 BEARING ASSY 1
9 26738G01 *BEARING-C CASE-MAIN BEAR COV 1
10 26708G01 *PIN-DOWEL-CRANKCASE-4CYC 2
11 ELBOW 1
12 GUIDE, DIPSTICK 1
13 26591G01 *FILTER-OIL-4CYC 1
14 26710G01 *O-RING-OIL FILTER-4CYC 1
16 26680G01 *BOLT & WASHER-M6X1X12MM-4-CYC 3
18 26712G01 *O-RING-CYLINDER HEAD-4CYC 1
19 26669G01 *PIN-DOWELL-4CYC 2
21 26723G01 *GASKET-BREATHER-INNER (4CYC) 1
22 72532G01 *PLATE-BREATHER-EH35C 1
24 26722G01 *GASKET-BREATHER-OUTER (4CYC) 1
25 26603G01 *COVER-BREATHER-COMPLETE-4CYC 1
27 26677G01 *BOLT-FLANGE-BREATHER COVER-4C 2
29 72535G01 *COVER-BELT-INNER-EH35C LATER FROM S/N 1003674 1
30 26629G01 *COVER-BELT (1 UNIT)-4CYC EARLY TO 1003673 1
31 72536G01 *SPRING-IDLER-EH35C LATER FROM S/N 1003674 1
32 26694G01 *SPRING-IDLER-4CYC EARLY TO 1003673 1
33 26681G01 *BOLT-FLG-RELIEF VALVE-4CYC 3
34 26626G01 BELT-TIMING-4-CYCLE 1
35 26627G01 *PULLEY-DRIVEN-4CYC 1
37 26628G01 *IDLER KIT-4CYC 1
38 26639G01 *BOLT/WASHER ASY-M8X1.25X20-4C 1
39 26696G01 *WASHER-PULLEY-DRIVEN-4CYC 1
40 26640G01 *BOLT-IDLER PIVOT-4CYC 1
41 26699G01 *WASHER-IDLER-4 CYC 1
42 26638G01 *BOLT/WASHER ASY-M6X1.0X16-4CY 1
43 26695G01 *WASHER-6.5MM X 22MM X 2MM-4CY 1
45 26630G01 *COVER-2-TIMING BELT-4CYC 1
46 26631G01 *GROMMET-TIMING BELT COVER-4CY 1
47 26678G01 *BOLT-FL-CAMSH COV-M6X1.0X12M 3
48 26613G01 *PLATE (2)-PULLEY-4CYC 1
49 26614G01 *PULLEY-DRIVE-4CYC 1
96 26593G01 *DIPSTICK/OIL GAUGE-4CYC-295CC 1
97 72530G01 *DIPSTK/GAGE-STRAIGHT-EH35C(SEE TEXT 1


18 26712G01 *O-RING-CYLINDER HEAD-4CYC 1
51 26606G01 *CONNECTING ROD ASSY. (4CYC) 2
52 26683G01 *BOLT-CONNECTING ROD-4CYC 4
53 26607G01 *PISTON ASSY.-STD. (4 CYCLE) 2
54 26660G01 *PISTON ASSY-.25MM O/S-4CYC 2
55 26661G01 *PISTON ASSY-.50MM O/S-4CYC 2
57 26608G01 *RING SET-STD-4CYC-EH29C 2
58 26662G01 *RING SET-.25MM O/S-4CYC 2
59 26663G01 *RING SET-.50MM O/S-4CYC 2
61 26609G01 *PISTON PIN (4 CYCLE) 2
62 26610G01 *CLIP - PISTON PIN (4 CYCLE) 2
64 26717G01 *GASKET-BEARING COVER-4CYC 1
66 26611G01 *SHAFT-BALANCER-4CYC 1
67 26689G01 *SPACER-1.0MM-BALANCER SHFT-4C 1
68 26690G01 *SPACER-1.2MM-BALANCER SHFT-4C 1
69 26688G01 *SPACER-.8MM-BALANCER SHAFT-4C 1
71 26693G01 *KEY-WOODRUFF-BALANCER SHFT-4C 1
72 72503G01 *CRANKSHAFT ASY-350CC 1
73 26605G01 *CRANKSHAFT ASY-4CYCLE-295CC 1
74 26739G01 *BEARING-MAIN BEARING COV-4CYC 1
75 26692G01 *KEY-WOODRUFF-CRANKSHAFT-4CYC 1
77 26684G01 *SPACER-.6MM-CRANKSHAFT-4CYC 1
78 26685G01 *SPACER-.8MM-CRANKSHAFT-4CYC 1
79 26686G01 *SPACER-1.0MM-CRANKSHAFT-4CYC 1
80 26687G01 *SPACER-1.2MM-CRANKSHAFT-4CYC 1
82 72513G01 *COVER-MAIN BEARING-EH35C 1
83 26592G01 *COVER-MAIN BEARING-COMP-4CYC 1
84 26738G01 *BEARING-C CASE-MAIN BEAR COV 1
85 26739G01 *BEARING-MAIN BEARING COV-4CYC 1
86 26742G01 *SEAL-OIL-CSHAFT(FAN SIDE)-4CY 1
88 26713G01 *GASKET-PLUG-CRANKCASE-4CYC 1
91 26681G01 *BOLT-FLG-RELIEF VALVE-4CYC 1
92 26597G01 *PLATE-RELEIF VALVE-4CYC 1
93 26664G01 *SPRING-RELIEF VLV-OIL PMP-4CY 1
94 26665G01 *BALL-STEEL-OIL PUMP-4CYC 1
98 26595G01 *ROTOR-OUTER-OIL PUMP-4CYC 1
99 26594G01 *ROTOR-INNER-OIL PUMP-4CYC 1
100 26711G01 *O-RING-OIL PUMP COVER-4CYC 1
101 26596G01 *COVER-OIL PUMP-4CYC 1
102 26680G01 *BOLT & WASHER-M6X1X12MM-4-CYC 3
105 26672G01 *BOLT / WASHER ASY-4CYC 2
106 26671G01 *BOLT & WASHER-M6X1X30MM-4CYC 6
189 72540G01 *PISTON ASSY-STD-.67MM-EH35C 2
190 72541G01 PISTON OVERSIZE .25MM 2
191 72542G01 PISTON (OVERSIZE .50MM) 2
193 72543G01 *RING SET-.67MM-EH35C 2
194 72544G01 PISTON RING SET OVERSIZE .25MM 2
195 72545G01 PISTON RING SET (OVERSIZE .500MM) 2



109 BOLT 1
110 WASHER, LOCK 1
111 SWITCH, OIL PRESSURE 1
112 26656G01 *WIRE (1)-OIL PRES.SW-4CYC 1
113 28458G01 "KIT, PULSER COIL ASSY RETROFIT" 1
114 26651G02 COIL-PULSAR-4CYC-FROM 1991 1
115 26707G01 BOLT/WASHER-M5 X 8 X 10MM-4CY 2
118 26703G01 *FAN ONLY-COOLING BLOWER-4CYC 1
119 72557G01 *FLYWHEEL-EH35C 1
120 WASHER, LOCK 2
121 26638G01 *BOLT/WASHER ASY-M6X1.0X16-4CY 6
123 26704G01 *BOLT-FLANGE-BLOWER HSG.-4CYC 3
124 26641G01 *BLOWER HOUSING ASSY 4-CYC 1
125 26691G01 *NUT-FLANGE-M22 X 1.5-4CYC 1
126 26676G01 *BOLT-FLANGED-M6X1.0X23MM-4CYC 1



129 26715G01 *SEAL-OIL-CAMSHAFT 1
130 26667G01 STUD-CYL HEAD-M6 X 1 X 105MM 2
131 26659G01 *VALVE GUIDE(OVER SIZE)-4CYC 4
132 26714G01 *SEAL-VALVE STEM 4
135 26643G01 *BAFFLE (2)-CYLINDER-4CYC 1
136 26681G01 *BOLT-FLG-RELIEF VALVE-4CYC 2
137 26600G01 *ROCKER COVER-4CYC 1
138 26601G01 *CAP-OIL FILLER-4CYC 1
139 26720G01 *O-RING-FILLER CAP-4CYC 1
140 26676G01 *BOLT-FLANGED-M6X1.0X23MM-4CYC 6
145 72511G01 *SPRING-VALVE-350CC 4
146 26719G01 *GASKET-ROCKER COVER-4CYC 1
147 26624G01 "*SPACER, ROCKER SHAFT" 2
150 26622G01 "*SCREW, ADJUSTING-M6X0.75X20MM" 4
151 26623G01 "*NUT, ROCKER ARM M6 X 0.75" 4
152 26625G01 "*SPRING, ROCKER SHAFT" 1
153 26615G01 *CAMSHAFT ASY-4CYC 1
154 26709G01 *PIN-DOWELL-4CYC 1
155 26620G01 *ROCKER SHAFT 1
156 26718G01 *GASKET-COVER-CAM-4CYC 1
157 26599G01 "*COVER, CAMSHAFT" 1
158 26678G01 *BOLT-FL-CAMSH COV-M6X1.0X12M 3
159 26679G01 *BOLT COVER CAM M6 X 1.0 1
161 26657G01 *BRACKET-IGNITION COIL-4CYC 1
162 26706G01 *NUT-FLANGE-IG COIL BKT-4CYC 1
163 26652G01 *COIL-IGNITION-4CYC 1
164 13632G1 NUT-METRIC-M6 X 1 2
165 26733G01 WIRE SET-SPARK PLUG-4 CYCLE 2
166 26733G02 WIRE SET-SPRK PLUG-4CY-IGN SUP AR
167 25523G2 SPARK PLUG-NGK-BP4ES-4CYC 2
169 26724G01 *GASKET-EXHAUST-4CYC 1
171 26633G01 *EXHAUST MANIFOLD COMP-4CYC 1
173 25531G1 *GASKET-MUFFLER-4CYC 1
174 25532G1 *BOLT/WASHER-8X1.25X18MM-4 CYC 4
176 26642G01 *BAFFLE (1)-CYLINDER-4CYC 1
177 26681G01 *BOLT-FLG-RELIEF VALVE-4CYC 6
178 26673G01 *FLANGE BOLT M8 X 1/25 X 50MM 4
180 72507G01 *VALVE-INTAKE-350CC 2
182 26675G01 *BOLT-FLG-M8 X 1.25 X 40MM-4CY 2
183 26673G01 *FLANGE BOLT M8 X 1/25 X 50MM 4
184 26674G01 *FLANGE BOLT M8 X 1.25 X 60MM 1
186 26716G01 *GASKET-HEAD-4CYC 1
187 72512G01 *GASKET-HEAD-350CC 1
196 26617G01 *VALVE-EXHAUST-4-CYCLE 2
197 72508G01 *VALVE-EXHAUST-350CC 2
198 26728G01 CHOKE BRACKET 1
199 26727G01 *GASKET-#1-AIR CLEANER-4CYC 1
200 72558G02 CARBURETTOR ASSY.C203 1
201 72558G01 "*CARBURETOR, 4 CYC" 1
204 26726G01 *GASKET #2-INSUL-CARB-4C-FUJI 1
205 26637G01 *INSULATOR-CARB-4CYC-FUJI 1
206 26726G01 *GASKET #2-INSUL-CARB-4C-FUJI 1



15 26632G01 *LINK-PIVOT-4CYC 1
29 72535G01 *COVER-BELT-INNER-EH35C LATER FROM S/N 1003674 1
32 26694G01 *SPRING-IDLER-4CYC EARLY TO 1003673 1
143 72510G01 *COLLET-VALVE RETAINER-350CC 8
144 26619G01 "*RETAINER, VALVE SPRING" 4
145 72511G01 *SPRING-VALVE-350CC 4
179 26616G01 *VALVE-INTAKE-4-CYCLE 2
180 72507G01 *VALVE-INTAKE-350CC 2

[NO NO NO E-Z-GO!]

That could be the EH-29 or EH-35.

[Cartmaster]

Yes its both engines, just some parts are different, like head, crank, crankcase pistons and rings. Most other parts are identical.

[singlemama02]

how to replace drive belt?

[ruredy]

You have to take and roll the old belt off the side of the driven clutch(the one on the rear end) while rotating all of it. Putting it on is the same only backwards. You put the belt on the drive clutch to start with, then you roll the belt on the driven clutch. not sure what model cart you have but on models with a 4 stroke engine you can put it in neutral. makes it easier to spin the clutches

[james.brew]

I have an ST 350 with a Robin 350CC engine. (EH35C) I need to know the "valve tappet clearance on both the exhaust and intake. Any help would be awesome! Thanks