|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
07-13-2018, 11:38 AM | #21 |
Getting Wild
Join Date: Jun 2018
Location: Ontario Canada
Posts: 122
|
Re: Still not working
Thanks I'll give them a call
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
07-13-2018, 11:43 AM | #22 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,418
|
Re: Still not working
Replace the PDS controller with the XCT400 control and SW180 solenoid.
|
07-13-2018, 01:01 PM | #23 |
Getting Wild
Join Date: Jun 2018
Location: Ontario Canada
Posts: 122
|
Re: Still not working
Thanks ---- for a guy that draws house plans, and has some mechanical experience, but not a lot, is it complicated to switch it over, and do you ship to Canada? ----- thanks for the reply
|
07-13-2018, 01:02 PM | #24 |
Getting Wild
Join Date: Jun 2018
Location: Ontario Canada
Posts: 122
|
Re: Still not working
I guess I'm more worried about the wiring harness and matching everything up
|
07-13-2018, 08:16 PM | #25 |
Gone Wild
Join Date: Apr 2013
Location: Deep Run, NC
Posts: 2,544
|
Re: Still not working
If you order the XCT 48400 for a PDS cart, it will pretty much be plug and play. Only thing you will have to change is the terminal ends on the F1 & F2 wires, which are provided. All you need is a crimper for small terminals.Sent from my SM-G930R4 using Tapatalk
|
07-14-2018, 04:44 AM | #26 |
Getting Wild
Join Date: Jun 2018
Location: Ontario Canada
Posts: 122
|
Re: Still not working
Thanks-- I can handle that ok
|
07-14-2018, 12:42 PM | #27 |
Getting Wild
Join Date: Jun 2018
Location: Ontario Canada
Posts: 122
|
Re: Still not working
I finally checked the pins in the J1 connector these are the readings. Pin 2 switch in N .3v
Pin 2 switch in R 37v Pin 3 switch in N 36v Pin 3 switch in F 36v Pin 9 switch in F 36v Pin 8 switch in R 36v Pin 8 switch in F. 17.5v with buzzer going Pin 7 36v Pin 6 36v Pin 10 switch in N the meter jumps all over Pin 10 switch in R the meter jumps all over Everything except the buzzer is new even the F/R switch-- not sure what to check next --- an Alltrax controller is going to cost about 800.00 so I'm hoping there is something else to try first --- it's hard to think a brand new controller and a rebuilt one would have the same problem---thanks for any advise anybody can give me |
07-14-2018, 12:47 PM | #28 |
Getting Wild
Join Date: Jun 2018
Location: Ontario Canada
Posts: 122
|
Re: Still not working
I forgot to mention the pack voltage is 37 v
|
07-14-2018, 02:06 PM | #29 | |
Gone Wild
Join Date: Jan 2014
Location: South Georgia
Posts: 1,120
|
Re: Still not working
Quote:
|
|
07-14-2018, 02:18 PM | #30 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: Still not working
Quote:
Fixing that problem may solve the other problems I highlighted in red. |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
My Trail Hog just stopped working, and then started working again. | Electric EZGO | |||
Working on G2 | Gas Yamaha | |||
Battery Charger Not Working - Cart Not Working | Electric EZGO | |||
Need Help 96 DCS not working | Electric EZGO | |||
WTB non working TXT gas | Golf Carts and Parts |