|
|
|||||||
| Big Block Talk! Everything about swapping a big block engine into your cart! |
  |
|
|
Thread Tools | Display Modes |
12-27-2022, 06:30 PM
|
#11 |
|
Gone Wild
Join Date: Jan 2014
Location: South Jersey
Posts: 623
|
Re: Mikuni carb on my briggs
Thanx Slo, Ill let you know what I find whenever I get good enough weather to install it
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
12-27-2022, 10:45 PM
|
#12 |
|
Searching for The Way
 Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,436
|
Re: Mikuni carb on my briggs
Good luck!
 |
|
|
|
|
12-29-2022, 09:41 AM
|
#13 |
|
Gone Wild
Join Date: Jan 2014
Location: South Jersey
Posts: 623
|
Re: Mikuni carb on my briggs
Mached up my carb last night and found the the bowl hits the crankcase breather nipple even with 2 spacers on the intake. If I cut the nipple off I wont even need to use spacers which would be ideal. I tried looking to see if they sell a different breather assembly but havent found anything. Any ideas around this? I dont wanna run a third spacer
|
|
|
|
|
12-31-2022, 08:52 AM
|
#14 |
|
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,436
|
Re: Mikuni carb on my briggs
The breather needs to be hooked up to your air intake so it can scavenge the engine of positive air pressure. I know people often vent that to atmosphere but that doesn't give the pcv system a true vacuum to do it's job. There are performance benefits to this, although minor. The biggest benefit would be keeping pressures in the crankcase from building up and causing blowby and blowing out gaskets. On mine I used two spacers and 3 gaskets, worked fine.
|
|
|
|
|
12-31-2022, 10:15 PM
|
#15 |
|
Sometime's............
Join Date: Oct 2007
Location: Tacoma Washington
Posts: 11,874
|
Re: Mikuni carb on my briggs
Were are the pictures ? This is what mine looks like...
|
|
|
|
|
01-02-2023, 07:25 AM
|
#16 |
|
Gone Wild
Join Date: Jan 2014
Location: South Jersey
Posts: 623
|
Re: Mikuni carb on my briggs
unfortunatly I cant mount the carb that side due to the gas tank being there. Not sure where I could run the breather line and hook it into. Slo, do you have any pics of your setup?
|
|
|
|
|
01-02-2023, 11:18 AM
|
#17 | |
|
Searching for The Way
Join Date: Oct 2009
Location: Medina, Ohio (NEOHIO)
Posts: 11,436
|
Re: Mikuni carb on my briggs
Quote:
https://www.buggiesgonewild.com/showthread.php?t=142756 |
|
|
|
|
|
01-03-2023, 12:01 PM
|
#18 |
|
Gone Wild
Join Date: Jan 2014
Location: South Jersey
Posts: 623
|
Re: Mikuni carb on my briggs
Slo, looking at your pics it looks like your briggs doesnt have the crankcase breather in the middle valley of the motor? The VM drain nipple with the hose at the bottom of the bowl hits the large nipple on the breather assembly on mine even with 2 spacers on the intake. If I cut the breather nipple off flush I would have no issues but im taking a chance of water intrusion into the motor.
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| Mikuni carb swap 23hp briggs | Clone Engine Swaps | |||
| carb tuning mikuni or eBay CV carb | Clone Engine Swaps | |||
| Carb rebuild kit for 97 Mikuni carb. | Gas Columbia ParCar | |||
| Hooking Up Briggs/Mikuni Fuel Pump? | Big Block Talk! | |||
| wtb mikuni carb | Golf Carts and Parts | |||
Linear Mode
