lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Modified Golf Carts > Design Center > Body and Paint


Post New Thread  Reply
 
Thread Tools Display Modes
Old 09-08-2009, 04:05 PM   #1
master66
Gone Wild
 
master66's Avatar
E-Z-GO
 
Join Date: May 2009
Location: Marysville Wa
Posts: 699
Default prep work for painting plastic bodies

I will try to give as much information as I can about doing prep work to plastic and metal bodies for paint. There seems to be quite a few questions about plastic and prep work so here goes, and remember these are just my personal preferences so you may use any product or method you wish.

Plastic bodies:
The very first thing is you can either remove the body parts to be worked or you can leave them on and mask everything, it,s personal preference but removing the parts usually works better. After that you need to scuff the whole body with either burgundy scotchbrite or sandpaper about 240 -400 grit dry paper, make sure you just remove the shine with the scuffing and not sand like crazy.
After scuffing now is the time to wipe it down with some wax and grease remover, wipe it on with one rag and wipe it off with another. Now you can do any bodywork that needs to be done, for filling scratches and gouges a polyester based finishing putty works the best for that, unlike the heavier "Bondo type" filler the finishing putty sand easier and doesn't tend to leave pinholes.I usually sand the putty with 240-320 grit dry paper then wax and grease again, remember wipe on wipe off.
Now is one of the most important parts "Adhesion promoter", this is a product that is sprayed on that softens up the plastic to accept primers and paints, if you do not do this step you risk all material you put on from here on out flaking or peeling off, especially if you are applying graphics later. Even if you are using Krylon Fusion I would still apply adhesion promoter. There are many different brands but I use either PPG or Dupont, make sure you read directions for applications and dry times.
Now you can pick a paint system and prime, if you are going to use automotive paint than I probably would not use bomb can primer, pick a primer that you're finished product material will accept. Prime accordingly, usually 2 to 3 good coats will do, then I usually sand with 240 grit if you are going to apply more primer later or 400-600 grit if this is you're finish sanding, and if you break through the primer in spots I would re prime and then spray a sealer on before applying color.If you have wet and dry sand paper you can wet sand if you like but I usually just use dry paper.
Just remember plenty of scuffing, adhesion promoter and plenty of wax and grease remover steps and you're job should turn out just fine.

Kevin
master66 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 09-08-2009, 04:54 PM   #2
SpoiledRotten
Conservatively Wild
 
SpoiledRotten's Avatar
E-Z-GO
 
Join Date: Aug 2009
Location: Below the Mason Dixon
Posts: 3,610
Default Re: prep work for painting plastic bodies

Very good, Kevin. I didn't see the "tack cloth" step though. Is that really not that necessary?
SpoiledRotten is offline   Reply With Quote
Old 09-08-2009, 05:01 PM   #3
galloway
Gone Wild
 
galloway's Avatar
Club Car
 
Join Date: Jul 2009
Location: Knoxville, TN
Posts: 495
Default Re: prep work for painting plastic bodies

Thanks Kevin for putting this out here. Glad you put that part about the promoter product I was wondering what I need to find to help out. I know with pvc pipe we use the purple primer to get the plastic nice and warm to weld to the other plastic. Just wondering how the paint worked.

Thanks Again.
galloway is offline   Reply With Quote
Old 09-08-2009, 07:16 PM   #4
essness
Not your usual outlaw
 
essness's Avatar
Yamaha
 
Join Date: Oct 2008
Location: Near Lake Geneva, WI
Posts: 20,061
Default Re: prep work for painting plastic bodies

Can we sticky this??
essness is offline   Reply With Quote
Old 09-08-2009, 07:39 PM   #5
tonyton
Gone Wild
 
tonyton's Avatar
E-Z-GO
 
Join Date: Jan 2009
Location: Alabama
Posts: 2,120
Default Re: prep work for painting plastic bodies

It needs to be stickied. He's already gone through this 100 times. Good job Kevin
tonyton is offline   Reply With Quote
Old 09-09-2009, 08:06 AM   #6
master66
Gone Wild
 
master66's Avatar
E-Z-GO
 
Join Date: May 2009
Location: Marysville Wa
Posts: 699
Default Re: prep work for painting plastic bodies

Quote:
Originally Posted by SpoiledRotten View Post
Very good, Kevin. I didn't see the "tack cloth" step though. Is that really not that necessary?
The tack cloth is really not needed untill you start spraying the color and clear because you will pretty much be sanding out any debris in the primer out anyway, good question though. If I have time I will try to do one on prepping fiberglass and metal bodies also if you guys think it is needed.
master66 is offline   Reply With Quote
Old 09-09-2009, 08:14 AM   #7
scottyb
Happy Carting
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 73,866
Default Re: prep work for painting plastic bodies

Great info Kevin ..... thank you!
scottyb is offline   Reply With Quote
Old 09-09-2009, 08:21 AM   #8
TheNewGuy
Admin/Moderator
 
TheNewGuy's Avatar
Yamaha
 
Join Date: Dec 2006
Location: Ohio
Posts: 18,135
Default Re: prep work for painting plastic bodies

Thanks Kevin.

TheNewGuy is offline   Reply With Quote
Old 09-13-2009, 07:28 PM   #9
hawkeyedm2003
Getting Wild
E-Z-GO
 
Join Date: Mar 2009
Location: Over there
Posts: 76
Default Re: prep work for painting plastic bodies

Great write up.

2 questions for a newb...

What is "bomb can primer"?

How is the adhesion promoter applied? (same as paint with a gun?)
hawkeyedm2003 is offline   Reply With Quote
Old 09-13-2009, 07:47 PM   #10
SpoiledRotten
Conservatively Wild
 
SpoiledRotten's Avatar
E-Z-GO
 
Join Date: Aug 2009
Location: Below the Mason Dixon
Posts: 3,610
Default Re: prep work for painting plastic bodies

Bomb can is a professionals name for rattle can spray paints from Walmart and other retailers.

Like instrumentalist call accompaniment tapes and CDs, canned music. They don't like it when you sing to "canned music". They'd rather you use the real thing.
SpoiledRotten is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Modified Golf Carts > Design Center > Body and Paint


Thread Tools
Display Modes


Similar Threads
Thread Forum
krylon no prep Body and Paint
Any tips on painting the raw plastic roof? Body and Paint
paint prep Body and Paint
Paint prep question Gas EZGO
How to Prep my cart Electric EZGO


All times are GMT -5. The time now is 06:12 AM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2024, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.