|
|
|||||||
| Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
  |
|
|
Thread Tools | Display Modes |
11-21-2009, 07:43 PM
|
#1 |
|
......................
 Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
G8 rear end
I got this G8 a wile back it was all apart when i got it the motor was out of it, the rear end was out and wile messing with it i found out that the bearing is bad i quess, how hard is it to fix this, I have no problem fixing it just dont know where to start,and if u look at the axel tube someone welded it but the axle spins good
and on the back plate of the brake drum u cant read it in the video so here it is--JN3-F7280-5034A52821-RH-- if that helps (Here's a video of it) |
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
11-22-2009, 02:24 PM
|
#2 |
|
......................
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: G8 rear end
Here's the motor that goes in that G8 I got some work to do, the motor spins by hand but not all the way around it will only spin so far and stop and then u have to spin it back the other way,it spins smooth, I think the vavles are stuck from the looks of the carb, but will see when I take it apart, I'll take a video of the whole think, how can I tell what size motor this is
 |
|
|
|
|
11-22-2009, 05:40 PM
|
#3 |
|
Gone Wild
Join Date: Nov 2007
Posts: 469
|
Re: G8 rear end
open it up & have a look I had one apart they are not so bad to fix
I have one for parts & a complet G8 rear end the c clip on the shaft seems to be finished you will need a spacer to fix that as far as the engine goes remove the clutch open the side cover you probably have a broken balancer inside |
|
|
|
|
11-22-2009, 06:24 PM
|
#4 |
|
......................
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: G8 rear end
Thanks for the info---I've built alot of motors just never had one of these apart yet I'll check that out,
on the rear end, I remove the axle first and then the axle tube, remove the clutch, when i split the case is all the gears going to fall out or will it stay in place |
|
|
|
|
11-22-2009, 06:31 PM
|
#5 |
|
Gone Wild
Join Date: Nov 2007
Posts: 469
|
Re: G8 rear end
if you go very carefull they will stay in place
|
|
|
|
|
11-22-2009, 07:04 PM
|
#6 |
|
......................
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: G8 rear end
This is what I was looking at a lot of parts in there,so number 2 is my problem, and you said there's a C clip on that shaft # 27,--- Thanks --
|
|
|
|
|
11-22-2009, 07:39 PM
|
#7 |
|
Gone Wild
Join Date: Nov 2007
Posts: 469
|
Re: G8 rear end
ya exatly but you will probably need a tube
if so let me know I will see if I still have one in the parts |
|
|
|
|
11-22-2009, 07:51 PM
|
#8 |
|
......................
Join Date: Apr 2009
Location: FT Lauderdale FL.
Posts: 16,416
|
Re: G8 rear end
Yea I was thinking the samething I don't like that welded one, Well see what it looks like when I get it apart,--I'am going to take a video of the hole thing, Thanks I'll get back to
|
|
|
|
|
|
||||||
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| CLUB CAR (GAS) REAR AXLE swap.....Are the gas and electric rear axles interchangeable | Gas Club Car | |||
| I need to change the rear axle - rear end oil | Gas Club Car | |||
Linear Mode
