|
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
05-12-2017, 09:21 AM | #1 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
New Altrax Controller on a G22 and having Runaway problems
just put a new alltrax xct 400 in a g22 we have here at the shop and after the instalation it is acting weird. when i push the pedal down it has a half second hesitation and then starts acclerating until it is going full speed and doesnt respond the pedal anymore once it starts going. so it doesnt matter if you just touch the throttle or floor it the motor will go full speed and will not turn off until i turn the key off and hit the brake. after you touch the pedal it goes into full runaway mode and just goes full speed on its own. anybody have any idea? do i have a bad controller, or a bad pedal or something else?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
05-12-2017, 09:25 AM | #2 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
model is XCT48400
|
05-12-2017, 09:26 AM | #3 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
i have a dumb question, can the throttle be setup backwards on it? like 5k-0 instead of 0-5k? would that cause the problems im having
|
05-12-2017, 09:41 AM | #4 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: New Altrax Controller on a G22 and having Runaway problems
Which model controller did you replace? Ge or Moric? Not "it was the stock one" , both were available stock. If it was Moric, it's a easy solution.
|
05-12-2017, 09:56 AM | #5 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
it was a Moric
|
05-12-2017, 09:56 AM | #6 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
whats the easy solution
|
05-12-2017, 10:17 AM | #7 |
Happy Carting
Join Date: Dec 2007
Location: Southern California
Posts: 73,358
|
Re: New Altrax Controller on a G22 and having Runaway problems
Check to see you have the correct throttle programmed. When the controller first powers up it gives a green blink code. That code is listed in the owners manual.
|
05-12-2017, 10:42 AM | #8 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
yea the sticker on it says g19-g22 0-5k but i guess i probably need to hook it up to a laptop to see if that is right. ive never needed to on an alltrax before so its all new to me.
|
05-12-2017, 11:29 AM | #9 |
Gone Wild
Join Date: Sep 2016
Posts: 375
|
Re: New Altrax Controller on a G22 and having Runaway problems
|
05-12-2017, 03:50 PM | #10 |
Over This Interview Is...
Join Date: Jun 2012
Location: AZ
Posts: 17,449
|
Re: New Altrax Controller on a G22 and having Runaway problems
Easy fix- Set controller check box "enable high side drive". Same setting by used for all Yamaha drives with Moric controller. But keep throttle set at Yamaha 0-5k. This is your likely problem, if you kept the cables set up as they originally were. You will need the laptop for this.
|
|
Thread Tools | |
Display Modes | |
|
Similar Threads | ||||
Thread | Forum | |||
Altrax XCT Controller | Electric EZGO | |||
Altrax SPM500 controller map | Electric Club Car | |||
EZGO DCS Altrax Controller, PQ Motor | Golf Carts and Parts | |||
instaling an altrax controller | Electric Club Car | |||
Altrax Controller Recommendations | Electric EZGO |