lifted club cars - lifted ezgo
Home FAQDonate Who's Online
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Yamaha
Electric Yamaha Electric Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles



Post New Thread  Reply
 
Thread Tools Display Modes
Old 04-21-2019, 04:04 AM   #1
georgia088
Gone Wild
 
Join Date: Jul 2012
Posts: 313
Default Yamaha g22e alltrax controller install not working

I have Yamaha g22e with a General Electric motor and fsip controller. I purchased the xct controller from Scotty. I installed it yesterday. I followed the diagram for the g19/g22 install. So, i connected/moved the wires labeled from the fsip controller to the new controller as follows:

FSIP CONTROLLER. ALLTRAX CONTROLLER
“Pos” ———> B+
A2 ———> B+
A1 ———> M- (j9)
F1. ———> F1 (j7)
F2. ———> F2 (j
“Neg”. ———> B-

Once the cart battery supply is connected and switched on I get the green blinking lights then solid green (this is normal correct?). When the pedal is pressed in both forward and reverse, the cart starts as if it wants to go, but then just jumps slowly either forward or backwards depending on direction of switch, and I get the error code: 1 green blink 2 red blinks (according to manual this is “battery under voltage”).

I am now looking at the manual and see there are two diagrams for g22. One for Moric controller and one for GE. I have neither. Mine is FSIP. I see the difference is that F1 and F2 are reversed from how I have it connected (F2 goes to the F1 slot and F1 to the F2 slot) and A2 goes to B- instead of B+ like I have it connected.

Should I change it to the way the second diagram has it? I honestly didn’t realize there were two different diagrams. I just saw the first and hooked it up that way. Now, I see there are two ways to do it. How should I proceed?

Thanks so much!!
georgia088 is offline   Reply With Quote
Alt Today
BGW

Golf car forum Sponsored Links

__________________
This advertising will not be shown in this way to registered members.
Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum
   
Old 04-21-2019, 02:35 PM   #2
cgtech
Over This Interview Is...
 
cgtech's Avatar
Yamaha
 
Join Date: Jun 2012
Location: AZ
Posts: 17,434
Default Re: Yamaha g22e alltrax controller install not working

Ok, solenoid clicks on when pedal pressed? (I bet it doesn't)
cgtech is offline   Reply With Quote
Old 04-21-2019, 03:15 PM   #3
georgia088
Gone Wild
 
Join Date: Jul 2012
Posts: 313
Default Re: Yamaha g22e alltrax controller install not working

I am not at it right now, but I donít think the solenoid clicked. What does this mean?
Thanks!
georgia088 is offline   Reply With Quote
Old 04-21-2019, 05:13 PM   #4
cgtech
Over This Interview Is...
 
cgtech's Avatar
Yamaha
 
Join Date: Jun 2012
Location: AZ
Posts: 17,434
Default Re: Yamaha g22e alltrax controller install not working

It means the controller isn't activating the solenoid, or the solenoid is bad. Time to hook up the laptop, the Alltrax software will tell you if the pedal switch is working, and things like that.
cgtech is offline   Reply With Quote
Old 04-21-2019, 06:04 PM   #5
georgia088
Gone Wild
 
Join Date: Jul 2012
Posts: 313
Default Re: Yamaha g22e alltrax controller install not working

The cart was working. I just changed the controller because the cart wouldnít go in reverse with the fsip controller. It was running fine in forward. Now itís a no go.
georgia088 is offline   Reply With Quote
Old 04-21-2019, 06:53 PM   #6
scottyb
go to cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 70,651
Default Re: Yamaha g22e alltrax controller install not working

I think calling Alltrax Tech is the best next step . See if they can tell you which controller you had in the cart originally so you know how to connect the cables.
scottyb is offline   Reply With Quote
Old 04-22-2019, 12:02 PM   #7
georgia088
Gone Wild
 
Join Date: Jul 2012
Posts: 313
Default Re: Yamaha g22e alltrax controller install not working

I emailed them the issue, and they said it was wired correctly. They said it sounds like a solenoid issue also. I don't understand because the solenoid is the one that was working with the other controller, and I haven't done anything to it other than move the wires from fsip controller to alltrax. Any ideas?

Thanks!
georgia088 is offline   Reply With Quote
Old 04-22-2019, 02:57 PM   #8
scottyb
go to cartsunlimited.net
 
scottyb's Avatar
E-Z-GO
 
Join Date: Dec 2007
Location: Southern California
Posts: 70,651
Default Re: Yamaha g22e alltrax controller install not working

Look for a fuse?
Use your meter to check and see if you are getting 48v between the 2 small solenoid posts when you try to go to activate the solenoid.
scottyb is offline   Reply With Quote
Old 04-22-2019, 03:12 PM   #9
georgia088
Gone Wild
 
Join Date: Jul 2012
Posts: 313
Default Re: Yamaha g22e alltrax controller install not working

No voltage across the small post on solenoid when pedal pressed. The only fuse I found was good. What next?
georgia088 is offline   Reply With Quote
Old 04-23-2019, 08:08 AM   #10
georgia088
Gone Wild
 
Join Date: Jul 2012
Posts: 313
Default Re: Yamaha g22e alltrax controller install not working

I spoke to the alltrax support line. They walked me through a few things, but they needed me to be able to connect to the controller with a cpu. I didn't have one at the particular time. I plan to call back this evening with the cpu connected.

In the mean time, can someone direct me to or explain to me the activation circuit of the g22? From my very limited understanding, The pedal is pressed-- which activates a micro switch that sends 48v to the xct controller-- the controller then does what to activate the solenoid??? What happens next? I know this will probably not do me any good in remedying the cart, but I would like to understand what is going on.

Thanks.
georgia088 is offline   Reply With Quote
Reply
Go Back   Buggies Gone Wild Golf Cart Forum > Golf Cart Repair and Troubleshooting > Electric Yamaha


Thread Tools
Display Modes


Similar Threads
Thread Forum
Alltrax SR controller install Electric EZGO
new Alltrax controller install ? Electric EZGO
2004 G22E Controller Upgrade to Alltrax Electric Yamaha
New Alltrax and Solenoid install: nothing working Electric Club Car
Alltrax DCX 500 motor controller install Electric Club Car


All times are GMT -5. The time now is 07:00 PM.


Club Car Electric | EZGO Electric | Lifted Golf Carts | Gas EZGO | Used Golf Carts and Parts

Powered by vBulletin® Version 3.8.9
Copyright ©2000 - 2021, vBulletin Solutions, Inc.
This Website and forum is the property of Buggiesgonewild.com. No material may be taken or duplicated in part or full without prior written consent of the owners of buggiesgonewild.com. © 2006-2017 Buggiesgonewild.com. All rights reserved.