|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
04-18-2011, 06:12 AM | #1 |
Not Yet Wild
Join Date: Sep 2010
Posts: 19
|
stop switch g1
Ok my cart is done. I'll post some pics later. Still have one problem. When running trying to go slow my cart does this di di di didi di. its only when i'm just barely pressing the pedal. just wondering if it could be the stop switch or something else.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-18-2011, 11:06 AM | #2 |
Gone Wild
Join Date: Mar 2010
Location: Eminence, IN
Posts: 534
|
Re: stop switch g1
it seems to be a pretty common thing that the butterfly is not adjusted right....check that first. Its the small threaded rod on the passenger side of the carb
|
04-18-2011, 12:36 PM | #3 |
Not Yet Wild
Join Date: Sep 2010
Posts: 19
|
Re: stop switch g1
thanks sounds easy enough. Ill check it out friday.
|
04-18-2011, 02:29 PM | #4 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: stop switch g1
And make sure the carb is sitting straight up/down not twisted in the intake. Should be able to press pedal and it will idle slow without cart moving, only after that should you press more and carb start to open.
|
04-19-2011, 08:14 AM | #5 |
Not Yet Wild
Join Date: Sep 2010
Posts: 19
|
Re: stop switch g1
The carb idle is fine. just that cutting in and out power wise at low speed. kinda annoying.lol.
|
04-19-2011, 09:34 AM | #6 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: stop switch g1
Usually the throttle is on part way, and people touch the pedal and let off because it goes too fast pedal on with throttle open. Its like turning the key on and off. If it stays running but surging, I would clean carb and look for leaks in intake and airbox areas. It could also be the crank seals going they will leak oil, you can spray them with wd40 or something to test them see if it runs different for a moment. Usually takes choke to start them with bad seals.
|
04-19-2011, 09:58 AM | #7 |
Not Yet Wild
Join Date: Sep 2010
Posts: 19
|
Re: stop switch g1
Sweet. Ill check it out i posted my build int the lifted carts area if yall wanna check it out
|
05-02-2011, 06:11 AM | #8 |
Not Yet Wild
Join Date: Sep 2010
Posts: 19
|
Re: stop switch g1
It was the butterfly. but it did take the top speed way down. Now the carb doesnt open all the way. is there another adjustment i can do to get the carb open. it seems there is not enough travel on the rod.
|
05-02-2011, 06:59 AM | #9 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: stop switch g1
You can adjust the linkage rods on most of them by screwing it in/out of the ends. Sometimes people move the pedal to make it closer to the floor, you can take it off and move it up a spline for more travel. When I do them I leave and inch of travel at top of pedal for idle, I can always get WOT on the floor. These carts are old hard to say what people did to them, what they adjusted/etc.
|
05-03-2011, 06:30 AM | #10 |
Not Yet Wild
Join Date: Sep 2010
Posts: 19
|
Re: stop switch g1
cool. I'll give it a try. thanks for the info.
|
Tags |
yamaha g1 gas |
|
|
Similar Threads | ||||
Thread | Forum | |||
forward/reverse switch change to toggle switch | Electric Club Car | |||
1994 G9KA-accelerator stop switch | Gas Yamaha | |||
Big block stop switch terminal | Big Block Talk! | |||
rebuild a 92 G9 stop switch | Electric Yamaha | |||
Just got a G9 need to know how to wire ignition switch to push pull switch ASAP! | Gas Yamaha |