|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
03-14-2019, 12:39 PM | #21 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: New Crowns or used Trojans for 36v to 48v conversion
I don't really have any flat runs, but that amperage sounds way low to me, for climbing hills. Mine generally runs 70 or so amps just cruisin' not climbing any real hills. Mine will hit 300 +/- climbing medium hills around me.
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
03-14-2019, 12:42 PM | #22 |
Not Yet Wild
Join Date: Feb 2019
Posts: 10
|
Re: New Crowns or used Trojans for 36v to 48v conversion
Figured out the logging feature. Had to save to a different folder than the Alltrax folder. Here is the Current and Voltage graph along with the throttle position. For some reason the throttle will only show 80% even though I'm on the floor, maybe that is the reason. I've also included the actual log file.
|
03-14-2019, 12:59 PM | #23 |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: New Crowns or used Trojans for 36v to 48v conversion
I had to adjust my ITS plunger to hit 100% with my old AXE. There may also be a way in the Toolkit.
|
03-14-2019, 01:41 PM | #24 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: New Crowns or used Trojans for 36v to 48v conversion
Quote:
However, the edited file posted indicates the throttle signal actually reaching the SR controller on the hill is only 80%. Since there were some 100% entries at the beginning of the file, I suspect there is some crosstalk at the in-line connector at the end of the gray cable from the pedal box. |
|
03-14-2019, 01:52 PM | #25 |
Not Yet Wild
Join Date: Feb 2019
Posts: 10
|
Re: New Crowns or used Trojans for 36v to 48v conversion
I've attached the zip file of the complete log.
I assume I would need to somehow shield the grey cable to prevent crosstalk. Any recommendations? Does everything else seem to be inline with what I can expect? |
03-14-2019, 02:15 PM | #26 | |
Gone Mad
Join Date: Oct 2009
Location: Buford, GA
Posts: 8,988
|
Re: New Crowns or used Trojans for 36v to 48v conversion
Quote:
|
|
03-14-2019, 03:06 PM | #27 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: New Crowns or used Trojans for 36v to 48v conversion
Quote:
What happens is the throttle wires (black and white) should have 10V between them when pedal is up (0% throttle) and 6V between them when the pedal is down. The green wire has battery pack voltage on it when the cart is ready to be driven and both green and red wires have battery pack voltage on them when pedal is pushed and pedal switch contacts close. Only going to 80% throttle indicates the voltage between the black and white wires is on dropping to 6.8V and the logical source for the extra 0.8V is the green and/or red wires. With ~50V available, it doesn't take much of a conductive path to add 0.8V to the throttle circuit. That connector might not be the source of the problem, but it is a common failure item, so getting rid of it may very well save you headaches in the future. The purpose of the connector was to make assembly easier on the production line. Other than that, it has little value. Thanks for the csv file. I'll load it into a spreadsheet and take a quick look for any red flags waving. |
|
03-14-2019, 03:49 PM | #28 | |
Not Yet Wild
Join Date: Feb 2019
Posts: 10
|
Re: New Crowns or used Trojans for 36v to 48v conversion
Quote:
|
|
03-14-2019, 04:05 PM | #29 |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: New Crowns or used Trojans for 36v to 48v conversion
The pack voltage dropped to 38.5V, but the battery amps was at 501.2A, the batteries aren't broken in yet and the temperature was probably than 80°F. That triggered the Lo-Battery flag that appears of the next line entry, but wouldn't be overly concerned about it unless it reoccurs often.
The flags I was looking for were the hi and low throttle under and over range, which often are set when there is cross-talk between the throttle and pedal switch circuits, but there isn't enough cross-talk to drive the throttle signal out of its normal range +/- tolerances. The Throttle Position column corresponds to the throttle voltage input to the SR controller and there are a few places that indicate there is a throttle signal when there shouldn't be. I see about 0.1V in some places and about 0.7V in others, and the expected reading of 0 in still others. So whatever the problem is, it is both intermittent and inconsistent. I'd get rid of the in-line connector and see if that fixed the problem and go on troubleshooting from that point is it doesn't. BTW: Divide the number in the throttle position by 4095 to get %throttle. |
03-14-2019, 04:17 PM | #30 | |
Techno-Nerd
Join Date: Jun 2011
Location: West Virginia
Posts: 19,654
|
Re: New Crowns or used Trojans for 36v to 48v conversion
Quote:
Is the pedal box clean and dry? Connect a DVM between the black and white wires at the controller and if at all possible, read the voltage while going uphill and you're only getting 80% throttle with pedal on floor. Also, when recording a data log file, when you let pedal return to the full upright position, take your foot completely off the pedal. (A foot resting on pedal might cause the slight throttle voltage I was seeing on the log.) |
|
|
|
Similar Threads | ||||
Thread | Forum | |||
Trojans | Electric EZGO | |||
Blew up some trojans | Electric EZGO | |||
My Trojans | Electric EZGO |