|
Electric EZGO Electric EZ GO Marathon, Medalist, TXT and RXV. |
|
Thread Tools | Display Modes |
04-16-2011, 01:45 PM | #41 |
Not Yet Wild
Join Date: Apr 2011
Location: Saraband Alabama
Posts: 45
|
Re: Have ? About my top speed
I get nothing on meter when I check the white and black wires
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-16-2011, 05:25 PM | #42 |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: Have ? About my top speed
My bad,
on a ITS you will have to have the switch on I guess. I was thinking of the older Pot Box version. Sorry! Just don't have it on the ground or hooked to the controller or it may take off on you. |
04-16-2011, 05:56 PM | #43 |
Not Yet Wild
Join Date: Apr 2011
Location: Saraband Alabama
Posts: 45
|
Re: Have ? About my top speed
Ok switch on still reeds nothing
|
04-16-2011, 06:06 PM | #44 |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: Have ? About my top speed
You have the meter set to Ohms. You are pressing the gas pedal down as you do this test right and getting nothing?
|
04-16-2011, 06:37 PM | #45 |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: Have ? About my top speed
CHECKING CONTROLLER OUTPUT
Connect (-) probe to M- terminal. Connect (+) probe to B+ terminal. Reading should indicate approx. 0 volts. Slowly depress accel. pedal. The reading should show the voltage increasing to battery voltage when fully depressed. If the voltage is at or near battery voltage and the motor is not turning, problem lies in either the forward/reverse switch, wiring or the motor. If the voltage increases by a few volts and then stops changing while the pedal is being depressed, remove the orange wire at the "Reverse Micro switch". If the voltage is not at or near battery voltage, replace the controller. If battery voltage is present, the problem lies in the reverse circuit. |
04-16-2011, 08:20 PM | #46 |
Not Yet Wild
Join Date: Apr 2011
Location: Saraband Alabama
Posts: 45
|
Re: Have ? About my top speed
The ITS has 0.225 clearance should i leave it or open it up the clearance
|
04-16-2011, 08:30 PM | #47 |
Not Yet Wild
Join Date: Apr 2011
Location: Saraband Alabama
Posts: 45
|
Re: Have ? About my top speed
Battery pack is at 36.6 at WOT getting 34.1
|
04-16-2011, 08:46 PM | #48 |
48/400/Alltrax HS motor
Join Date: Jan 2007
Location: Liberty SC, Garden City SC
Posts: 6,190
|
Re: Have ? About my top speed
All of that sounds right. The clearance should be 17/64 which is .2656. You may want to open it up a little more.
|
|
|
Similar Threads | ||||
Thread | Forum | |||
MCOR? Speed Sensor? Controller? Cart Runs at half speed. Advice, please. | Electric Club Car | |||
new high speed motor and still no speed | Electric EZGO | |||
1985 G1 Runs fine low speed , high speed run for a mile then fall on its face | Gas Yamaha | |||
more speed without sacrificing low speed control | Gas Club Car | |||
need for speed 48V CC | Electric Club Car |