|
|
|||||||
| Gas EZGO Gas EZGO Marathon, Medalist, TXT and RXV. |
  |
|
|
Thread Tools | Display Modes |
03-19-2011, 10:51 AM
|
#1 |
|
Not Yet Wild
Join Date: Feb 2009
Location: Indiana
Posts: 43
|
Trying to remove drive clutch.
I've found info on removing the secondary clutch but I can't seem to find anything on removing drive clutch. Anybody have any info on that?
|
|
|
 Today
|
|
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
|
03-19-2011, 11:57 AM
|
#2 |
|
Happy Carting
 Join Date: Dec 2007
Location: Southern California
Posts: 73,399
|
Re: Trying to remove drive clutch.
Buy the puller. Remove the center bolt & fill the bolt hole with grease and install puller with electric or air impact hammer
 |
|
|
|
|
03-19-2011, 11:57 AM
|
#3 |
|
I Refuse To Get Stuck!!!
Join Date: Jun 2010
Location: Hilton,NY
Posts: 5,427
|
Re: Trying to remove drive clutch.
You need a clutch removal-tool(see site-sponsors,about $20-$25).Remove the center-bolt,then install the tool and tighten.It will pop off the shaft-taper.
|
|
|
|
|
03-19-2011, 12:23 PM
|
#4 |
|
Not Yet Wild
Join Date: Feb 2009
Location: Indiana
Posts: 43
|
Re: Trying to remove drive clutch.
I did see there was a puller, just thought possibly there was a trick. I will buy the puller, which sponsor?
|
|
|
|
|
03-19-2011, 12:24 PM
|
#5 |
|
Not Yet Wild
Join Date: Feb 2009
Location: Indiana
Posts: 43
|
Re: Trying to remove drive clutch.
Oh and thank you for the advice.
|
|
|
|
|
03-19-2011, 12:46 PM
|
#6 |
|
Getting Wild
Join Date: Jul 2009
Location: Ludington MI
Posts: 123
|
Re: Trying to remove drive clutch.
I would say http://www.mikesmotortoys.com/ Just because of past experience dealing with him, When I was down and had a trip planned but NEEDED a puller he sent me his puller from the shop box because ordering one meant three more days. This is just one example of many.
|
|
|
|
|
03-21-2011, 09:35 PM
|
#7 |
|
Not Yet Wild
Join Date: Sep 2010
Location: Iowa
Posts: 13
|
Re: Trying to remove drive clutch.
I think all you need is a 2" x 3/4" fine thread bolt. and a 3" long x 5/8" solid stock shaft. ( a couple of deep well sockets also work) beats buying one for twenty five bucks. bolt only cost you a couple of bucks. stick the shaft down the tube (hollow shaft) then screw the bolt in. tighten. should start to pop off the taper. good luck. just trying to save you a few bucks.
|
|
|
|
|
03-21-2011, 10:23 PM
|
#8 |
|
Not Yet Wild
Join Date: Feb 2009
Location: Indiana
Posts: 43
|
Re: Trying to remove drive clutch.
No, appreciate the tip. Can't see buying the tool for a one time use. Thanks again.
|
|
|
|
|
03-21-2011, 10:28 PM
|
#9 |
|
Not Yet Wild
Join Date: Feb 2009
Location: Indiana
Posts: 43
|
Re: Trying to remove drive clutch.
Also, I didn't really realize how the clutch came off, so I removed the 8-10mm bolts on the outer plate of the clutch.
Question, is there a preload on that spring or is the closest hole that line up with the bolt holes???? Don't wanna put it back on and have it not function correctly. I was going to mark it but I was watching tv and wasn't paying attention. **** tv in the garage, should have never put that **** thing in there. Screwed up alot of things watching that. |
|
|
|
|
03-22-2011, 06:12 AM
|
#10 |
|
no clue
Join Date: Sep 2009
Location: spicewood, texas
Posts: 3,308
|
Re: Trying to remove drive clutch.
if you have a 2 cycle engine, there is no preload since it has to work in both directions. don't know about 4 cycle. here is my homemade puller. used a piece of rebar.
 |
|
|
|
|
|
||||||
| Thread Tools | |
| Display Modes | |
|
|
Similar Threads
|
||||
| Thread | Forum | |||
| need to remove my clutch | Gas Club Car | |||
| how to remove clutch | Gas Club Car | |||
| Can I remove drive clutch while in cart? | Gas EZGO | |||
| how to remove the clutch ???? | Gas Club Car | |||
| How do I remove the driven clutch? | Gas EZGO | |||
Linear Mode
