![]() |
|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
![]() ![]() |
|
Thread Tools | Display Modes |
![]() |
#1 |
Gone Wild
Join Date: Nov 2007
Posts: 469
|
![]() Here is a way to modify your governor to be wide open without having to play around try to figure out how to re align the throttle cables
1- Loosen the 10mm nut if you already have it cranked up , (it need to be stock) 2- Remove the plastic black cover at the back & remove the basket if you still have one At the lower part of the governor there is a bolt with a 10mm nut you loosen it so you can pry up the governor about 1/4 of an inch of the shaft you will notice that it is D shaped you take a 5/16 drill bit & round up the bracket so it will spin freely on the shaft Put it back in place Use a little lock tight or nail polish on the bolt & just tighten it by hand to keep from loosing it This way you have full throttle no restriction & all runs smooth like before, Change you oil to synthetic 1 liter of 10w30 Very important don’t hold it to the floor going downhill not to blow it up Good Luck Cart de Golf this might work on other models I havent tryed it Last edited by cart de golf; 11-27-2009 at 09:23 PM.. Reason: more info |
![]() |
![]() |
![]() |
|
![]() __________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
![]() |
#2 |
Admin/Moderator
![]() ![]() Join Date: Dec 2006
Location: Ohio
Posts: 17,838
|
![]() Thank you sir!
|
Ron
![]() PLEASE VISIT Our Sponsors * BGW GEAR The Store The G2 Project * Swing Arm Drop & Repair * Geep1 Project |
|
![]() |
![]() |
![]() |
#3 |
Vegas modded 420
![]() ![]() Join Date: Jun 2009
Location: West MI
Posts: 15,422
|
![]() It works on most Yamahas. Some carts you need to put a spring on the arm to keep it from lifting off the shaft, and some to also act as a return spring as some the governor does much of the return force even at rest. A G9 needs a spring for both issues, but a simple automotive carb throttle spring works well. That said for me this method has worked better than putting the cable on the carb.
|
![]() |
![]() |
![]() |
#4 |
Not Yet Wild
![]() Join Date: Mar 2010
Location: The Villages, FL.
Posts: 42
|
![]() I have a 2008 'Drive". Has anyone attempted this modification? Successfull? Thanks for your replies.
|
![]() |
![]() |
![]() |
#5 |
Gone Wild
Join Date: Nov 2007
Posts: 469
|
![]() take a picture of the governor I will let you know if it works
|
![]() |
![]() |
![]() |
#6 |
Not Yet Wild
![]() Join Date: Feb 2010
Location: Niagara Falls, N.Y.
Posts: 64
|
![]() i did this mod on my 99 g16. It increased top speed to 22-23 mph (why not 29-30) and also now i notice at low speeds it turns on and off ??? any suggestions?
|
![]() |
![]() |
![]() |
#7 |
Gone Wild
Join Date: Nov 2007
Posts: 469
|
![]() make sure the shaft spins inside the governor no hold back
for 30 mph you will need to do air cleaner jet ect. |
![]() |
![]() |
![]() |
#8 |
Getting Wild
![]() Join Date: Feb 2010
Location: Lexington, KY
Posts: 111
|
![]() What is the risk to the engine when bypassing the governor?
Thanks |
![]() |
![]() |
![]() |
#9 |
maintaining a low profile
![]() ![]() Join Date: Oct 2009
Location: SW Virginia USA
Posts: 6,299
|
![]() Just be mindful of your RPMs, and don't hold the throttle wide open going down hills.
|
![]() |
![]() |
![]() |
#10 |
Gone Wild
Join Date: Nov 2007
Posts: 469
|
![]() I have had mine full trottle on flat complet summer no problem with syntetic
10W30 motor oil like Dave said watch if you going down hill dont hold it full open it might over rev |
![]() |
![]() |
![]() |
|
Thread Tools | |
Display Modes | |
|
![]() |
||||
Thread | Forum | |||
Governor question | Gas Yamaha | |||
88 ez go governor | Gas EZGO | |||
governor | Gas Club Car |