|
Gas Yamaha Gas Yamaha Golf Cars; G1 through "The Drive" and U-Max Utility Vehicles |
|
Thread Tools | Display Modes |
04-18-2017, 09:55 PM | #11 |
Not Yet Wild
Join Date: Mar 2014
Posts: 11
|
Re: new to me 01-G16 need help plz
Can I or is there any benefit in removing the governor? If so how is it done?
|
Today | |
Sponsored Links
__________________
This advertising will not be shown in this way to registered members. Register your free account today and become a member on Buggies Gone Wild Golf Cart Forum |
|
04-18-2017, 10:57 PM | #12 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: new to me 01-G16 need help plz
You can remove it from the rear, I will if I ever split the case. Most don't get in there and have no issues with it. There is a sticky about disconnecting it from the engine, you get a couple mph from having it cranked full in there is not much difference on most carts I've done. One I tested with 22 tires did 27 with governor and 30 without, but took a long run to get there.
|
04-23-2017, 09:51 AM | #13 |
Not Yet Wild
Join Date: Mar 2014
Posts: 11
|
Re: new to me 01-G16 need help plz
Good morning,
I got the rear back together but now the forward and reverse are backwards, I followed the instructions " Install countershaft and forward wheel gear "marked F" with thick silver color thrust washer. Could the gear selection lever be on wrong? Or will I have to break the case down again? Thanks, |
04-23-2017, 02:01 PM | #14 |
Vegas modded 420
Join Date: Jun 2009
Location: West MI
Posts: 15,445
|
Re: new to me 01-G16 need help plz
I can't help you on that one, my manual is G9 and think its different. If you don't have the outside arm on backwards or something its likely inside unfortunately.
|
04-23-2017, 06:30 PM | #15 |
Not Yet Wild
Join Date: Mar 2011
Location: goldsboro,n.c.
Posts: 46
|
Re: new to me 01-G16 need help plz
just switch the shifter cables on the rear end.
|
04-23-2017, 07:52 PM | #16 |
Not Yet Wild
Join Date: Mar 2014
Posts: 11
|
Re: new to me 01-G16 need help plz
Evidently I had a moment, that fixed it.
The drive belt on this thing is Very loose, I measured the top and it's 1.13" which is showing in spec 1.06-1.22 I think. But it could be stretched I guess. I'll order a new one and maybe a heavier secondary spring to try. |
04-24-2017, 05:49 AM | #17 |
Not Yet Wild
Join Date: Mar 2011
Location: goldsboro,n.c.
Posts: 46
|
Re: new to me 01-G16 need help plz
i don't know if you did,but you can leave the plastic washer out of the driven pulley and that will tighten up the belt.also the yamaha sheaves wear a lot and that will make belt loose.i've worked at a yamaha dealer for 11 years and seen a few yamaha tricks and problems.
|
04-24-2017, 06:38 AM | #18 |
Not Yet Wild
Join Date: Mar 2014
Posts: 11
|
Re: new to me 01-G16 need help plz
Since I Cough cough kinda brike part of the secondary sheave I bought a new one with I'm guessing a regular spring and I did put the plastic spacer in.
|
04-25-2017, 05:57 PM | #19 |
Not Yet Wild
Join Date: Mar 2014
Posts: 11
|
Re: new to me 01-G16 need help plz
another ? The drive clutch is making a loud sound so it's probably time to either R&R or put a different one on. I found some new ones for 200ish, what would parts cost to R&R and where's a good source? And tie rods or ends?
Thanks |